Toro TimeCutter SW 4200 Скачать руководство пользователя

Страница: 89 / 142

MOWER DECK

6-8

Toro TimeCutter SS/MX/ZS Service Manual

50 Inch Fabricated Deck

(Fig� 098)

Fig. 098

PICT-1065

Inspecting the Belts

Service Interval: Every 25 hours – Check the belts for

wear�

Check the belts for cracks, frayed edges, burn marks or

any other damage� Replace damaged belts�

PTO Belt Replacement

1� Park the unit on a level surface and disengage the

PTO switch�

2� Move the motion control levers outward to the park

position, stop engine, remove key, and wait for all

moving parts to stop before leaving the operating

position�

3� Set the height-of-cut to the lowest cutting position�

4� If necessary, remove the belt covers�

5� If necessary, loosen belt guide to allow belt past (32”

only)�

6� Using a spring tool, (Toro part no� 92-5771), remove

the idler spring from the deck hook to relieve idler

pulley tension� Roll the belt off of the pulley(s)�

7� Route the new belt around the engine pulley and

deck pulley�

8� Using a spring tool, (Toro part no� 92-5771), connect

the idler spring to the deck hook while placing

tension on the idler pulley and deck belt�

Note: Do not install idler/tensioner spring before

wrapping belt around pulleys. Excessive

spring stretch will occur.

A� Idler pulley

E� Engine pulley

B� Deck belt

F� Spring tool

C� Spindle pulley

G� Deck handles

D� Spring

Содержание TimeCutter SW 4200















































































































































Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды

Toro TimeCutter SW 4200, Руководство по обслуживанию

Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды