Toro TimeCutter SW 4200 Скачать руководство пользователя

Страница: 28 / 142

CHASSIS

3-5

Toro TimeCutter SW/SWX Service Manual

Pod / Fender Removal – LH

1. Raise seat and disconnect battery terminals.

2. Unscrew fuel cap. With a clean, long, needle nose

pliers, reach into fuel tank and grab fuel cap tether

base (D). Pull upward and flex tether base to remove

fuel cap from fuel tank assembly (Fig. 011).

Pod / Fender Installation – LH

1. Maneuver LH fender into position.

Note: The LH control lever must pass through the

LH fender during removal and installation.

2. Install the (3) screws (E) that secure the LH fender

to the frame and torque to specification – 7 ft-lbs.

(9 Nm).

3. Fully install the fuel cap tether base into fuel tank.

Install and tighten fuel cap.

4. Connect battery terminals, and lower seat.

(Fig. 012)

Fig. 011

PICT-1039

3. Remove the (3) screws (E) securing the LH fender to

the unit frame (Fig. 012).

4. Maneuver LH fender up and off frame.

Note: The LH control lever must pass through the

LH fender during removal and installation.

Fig. 012

PICT-1041

Содержание TimeCutter SW 4200















































































































































Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды

Toro TimeCutter SW 4200, Руководство по обслуживанию

Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды