Toro TimeCutter SW 4200 Скачать руководство пользователя

Страница: 37 / 142

CHASSIS

3-14

Toro TimeCutter SW/SWX Service Manual

Pod / Fender Support Installation

1. Position the Pod / Fender support bracket onto the

chassis.

2. Install the fasteners (A, B and C) that secure the

support to the chassis and torque to specification –

17 ft-lbs. (23 Nm).

3. Properly route the fuel lines / wire harness and

secure with cable ties (if needed).

4. Install hydro tank reservoir (SWX models only).

5. Install and connect hour meter (if equipped).

6. Install fuel tank and fenders.

7. Verify proper cable, wire harness and hose routing.

8. Connect battery terminals and lower seat

9. Verify proper unit function.

Pod / Fender Support Service

Pod / Fender Support Removal

(SWX Shown)

1. Raise seat and disconnect battery terminals.

2. Remove fenders and fuel tank as shown in this

chapter.

3. Take note of cable and harness routing for

reassembly.

4. Disconnect and remove the hour meter (if equipped).

5. Remove the fasteners (A) attaching the hydro

reservoir to the support bracket (SWX models only).

6. Remove the cable ties that secure the fuel lines /

wire harness cables (if equipped).

7. Remove the fasteners (B) securing the (2) rear

supports to the frame.

8. Remove the fasteners (C) securing the front fender

support to the frame.

9. Remove the Pod / Fender support bracket from the

chassis.

(Fig. 025)

Fig. 025

PICT-1060

Содержание TimeCutter SW 4200















































































































































Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды

Toro TimeCutter SW 4200, Руководство по обслуживанию

Результаты поиска

Содержание TimeCutter SW 4200

Отзывы:

Похожие инструкции для TimeCutter SW 4200

Бренды по названию

Популярные бренды