Brave BRPRC108HEB Скачать руководство пользователя

Страница: 1 / 24

BRPRC108HE

REV B

2/2020

OWNER’S MANUAL FOR:

44” Rough Cut Mower

w/ Elec. Clutch Blade Engagement

This machine is intended for use behind a tractor, ATV or UTV

to cut field, brush and saplings up to 2” thick.

Any Questions, Comments, Problems or Parts Orders

Call BRAVE Product Support 1-800-350-8739

WARNING

READ and UNDERSTAND this manual completely before using rough cut mower.

All operators of this equipment must read and completely understand all safety information, operating instructions,

maintenance and storage instructions. Failure to properly operate and maintain the mower could result in serious injury or

death to the operator and bystanders from moving parts that can cut, amputate, flying objects, burns, fire or explosion or

carbon monoxide poisoning and be aware of the following hazards.

•

WARNING

: Keep all guards and shields in place to avoid injury.

•

DANGER

: Do not operate the rough cut mower near people. Debris can be thrown hundreds of feet. Clear work area of

foreign objects and debris. Debris thrown by rough cut mower can cause serious injury or death.

•

CAUTION

: Avoid fires. Keep the machine clean of debris, trash and any other flammable material.

•

WARNING

: Tighten all nuts and bolts before starting. Replace or repair any safety device, bolts, etc if damaged or worn.

•

DANGER

: Stay clear of rotating blades. Keep hands and feet away.

•

DANGER

: Never operate rough cut mower without it mounted securely to the tow vehicle.

•

WARNING

: Wear protective clothing. Wear close-fitting clothing and other protective devices appropriate for the job.

•

DANGER

: Keep riders off machine. Riders can be seriously injured or killed by entanglement or by falling.

•

DANGER

: Exercise caution while working near machine. Failure to heed warnings may lead to serious injury or death.

•

DANGER

: Always maintain a safety distance. Never operate rough cut mower with bystander’s present. The rough cut

mower creates a serious discharge hazard. Never point the discharge direction at anyone. Be aware of where bystanders

are located, especially children. Never assume they will remain where you last saw them. Be sure to know what is in the

path of the discharge area.

STOP!

ADD OIL TO ENGINE BEFORE USING: Engine is shipped without oil. DO NOT start rough cut mower without first adding oil.

INSPECT COMPONENTS: Closely inspect to make sure no components are missing or damaged.

See Initial Unpacking and Set-up for instructions and for whom to contact to report missing or damaged parts.

ITEM NUMBERS:

BRPRC108HEB

MANUAL SERIAL TAG HERE

Содержание BRPRC108HEB

























Результаты поиска

Содержание BRPRC108HEB

Отзывы:

Похожие инструкции для BRPRC108HEB

Бренды по названию

Популярные бренды

Brave BRPRC108HEB, Руководство пользователя

Результаты поиска

Содержание BRPRC108HEB

Отзывы:

Похожие инструкции для BRPRC108HEB

Бренды по названию

Популярные бренды