Brave BRPRC108HEB Скачать руководство пользователя

Страница: 2 / 24

BRPRC108HE, REV B

REV 3/20

SAFETY INTRODUCTION

Your safety, and the safety of others, is very important. To help you make informed

decisions about safety, we have provided operating procedures and other information on

labels and in this manual. This information alerts you to potential hazards that could hurt

you or others.

This safety alert symbol is used to indicate safety instructions. Follow these

instructions to avoid personal injury and/or property damage. Read and follow all

instructions in this manual and the included engine manual.

You will find important safety information in a variety of forms, including:

Safety Labels

– on the mower.

Safety Messages

– preceded by a safety alert symbol and one of three signal

words:

DANGER, WARNING,

CAUTION.

These signal words mean:

DANGER:

Indicates an imminently hazardous situation that, if not avoided, will result in

death or serious injury. This signal word is to be limited to the most extreme situations

typically for machine components which, for functional purposes, cannot be guarded.

WARNING:

Indicates a potentially hazardous situation that, if not avoided, could result in

death or serious injury, and includes hazards that are exposed when guards are removed.

It may also be used to alert against unsafe practices.

CAUTION:

Indicates a potentially hazardous situation that, if not avoided, may result in

minor or moderate injury. It may also be used to alert against unsafe practices.

This entire manual is filled with important safety information. Please read it

carefully.

Содержание BRPRC108HEB

























Результаты поиска

Содержание BRPRC108HEB

Отзывы:

Похожие инструкции для BRPRC108HEB

Бренды по названию

Популярные бренды

Brave BRPRC108HEB, Руководство пользователя

Результаты поиска

Содержание BRPRC108HEB

Отзывы:

Похожие инструкции для BRPRC108HEB

Бренды по названию

Популярные бренды