Toro 41107-210000101 Скачать руководство пользователя

Страница: 9 / 80

SAFETY AND INSTRUCTION DECALS

The following safety and instruction decals are installed on the vehicle. If any become damaged

or illegible, replace them. Decal part numbers are listed below and in the parts catalog. Order

replacements from your Authorized TORO Distributor.

Part No. 62-5550: Located on Front of

Front Console.

Part No. 100-6775: Located on

Top of Fuel Tank.

Part No. 100-8620: Located On Seat Mount Panel.

SPRAY 2

(3-5 MPH)

SPRAY 1

(2-3 MPH)

IMPORTANT

IMPROPER USE OF RANGE SELECTOR CAN DAMAGE
TRANSMISSION.

CHANGE THE RANGE SELECTOR ONLY WHILE

VEHICLE IS STATIONARY AND ENGINE IS AT LOW IDLE.

READ AND UNDERSTAND OPERATOR'S MANUAL

BEFORE OPERATING.

OPERATING INSTRUCTIONS

STARTING:

1. SIT IN OPERATOR'S SEAT

2. ENGAGE PARKING BRAKE & DEPRESS BRAKE PEDAL
3. PLACE RANGE SELECTOR IN NEUTRAL
4. START ENGINE
5. SELECT SPEED RANGE
6. RELEASE PARKING BRAKE
7. DEPRESS ACCELERATOR PEDAL UNTIL DESIRED SPEED IS REACHED

STOPPING OR CHANGING SPEED RANGE:

1. DEPRESS BRAKE PEDAL UNTIL VEHICLE COMES TO A HALT
2. ALLOW ENGINE TO RETURN TO LOW IDLE
3. SELECT NEW SPEED RANGE & RESUME OPERATION

RETURN RANGE SELECTOR TO NEUTRAL
ENGAGE PARKING BRAKE
SHUT ENGINE OFF & REMOVE KEY

SPRAY 3

(0-11 MPH)

100-8454

Part No. 100-8454: Located on

Lower Left Console.

Part No. 100-8577: Located on

Agitation Valve

Part No. 104-8882: Located On

Spray Valve Console Top

Part No. 104-8749: Located On

Spray Valve Console Panel

Содержание 41107-210000101

















































































Результаты поиска

Содержание 41107-210000101

Отзывы:

Похожие инструкции для 41107-210000101

Бренды по названию

Популярные бренды

Toro 41107-210000101, Руководство оператора и инструкция по установке

Результаты поиска

Содержание 41107-210000101

Отзывы:

Похожие инструкции для 41107-210000101

Бренды по названию

Популярные бренды