Toro 41107-210000101 Скачать руководство пользователя

Страница: 50 / 80

NOZZLE SELECTION L/HA

BEFORE SPRAYING

See the nozzle chart on pages 56 & 57 to be sure

that your spray nozzles have the capacity

necessary to achieve the application rate

selected.

To select the proper nozzle, you need to know:

1. Recommended chemical application rate in

liters per hectare.

2. Average Vehicle speed in kilometers per hour.

3. Nozzle spacing (20 inches or 50 centimeters).

With this information you can calculate the

volume per minute per nozzle, using the formulas

to the right.

L/HA

(METRIC) FORMULA:

L/min

L/ha x km/h x 50 cm

(Per nozzle)

60,000

Use L/min and Pressure to select appropriate

nozzle from chart below .

EXAMPLE (

L/HA

FORMULA):

Application Rate = 907 L/hectare

Vehicle Speed = 5 km/h

Nozzle Spacing = 50 cm

907 L/ha x 5 km/h x 50 = 3.78 L/min.

60,000

(per nozzle)

With 3.78 L/min and a pressure at 275 kPa you

would select nozzle No. 95-9188.

See the nozzle chart on pages 52-55 to be sure

that your spray nozzles have the capacity neces-

sary to achieve the application rate selected.

To select the proper nozzle, you need to know:

1. Recommended chemical application rate in

gallons per acre or gallons per 1000 sq. ft.

2. Average Vehicle speed in Miles per hour.

3. Nozzle spacing (20 inches or 50 centimeters).

With this information you can calculate the volume

per minute per nozzle using the formulas to the

right. Then select the proper nozzle from the

following charts.

BEFORE SPRAYING

NOZZLE SELECTION GPA/GAL/1000 FT

EXAMPLE (

GPA

FORMULA)

Application Rate = 44.6 Gallons/Acre

Vehicle Speed = 4 M.P.H.

Nozzle Spacing = 20 inches

44.6 G.P.A. x 4 M.P.H. x 20

.60 G.P.M.

5940

(per nozzle)

With .60 G.P.M. and a pressure of 40 psi you would

select Nozzle No. 95-9224.

EXAMPLE (

GAL/1000 FT

FORMULA):

Application Rate = 1.02 Gal./1000 sq. ft.

Vehicle Speed = 4 M.P.H.

Nozzle Spacing = 20 inches

1.02 GAL/1000 FT x 4 M.P.H. x 20 = .60 G.P.M.

137

(per nozzle)

With .60 GPM and a pressure of 40 psi, you would

select nozzle no. 95-9224.

Содержание 41107-210000101

















































































Результаты поиска

Содержание 41107-210000101

Отзывы:

Похожие инструкции для 41107-210000101

Бренды по названию

Популярные бренды

Toro 41107-210000101, Руководство оператора и инструкция по установке

Результаты поиска

Содержание 41107-210000101

Отзывы:

Похожие инструкции для 41107-210000101

Бренды по названию

Популярные бренды