Toro 41107-210000101 Скачать руководство пользователя

Страница: 63 / 80

SPRAYER CALIBRATION

Attach Supply Hose to Anti-siphon device and

fill the Tank half full with clean clear water.

1927

FIG. 6

. Drive the Vehicle in the desired Shift Range

and at the target operating speed with the Pump

and all Boom Sections on. Use the Pressure

Control Valve to obtain the desired application rate

on the Spray Pro. When the desired rate is

obtained, verify that the spray pressure is within

the operating range for the nozzle being used.

Continue with boom bypass valve adjustment if

never performed or nozzles have been changed.

Follow the nozzle selection method on page

50 to select the proper nozzle for the desired

application rate, operating pressure and target

speed.

CAUTION

In order to avoid potential for an

accident or injury, choose a wide open

area without obstructions to perform the

following mobile spray calibration

process.

IMPORTANT: INSPECT AND CLEAN ALL

SYSTEM COMPONENTS BEFORE SPRAYING,

INCLUDING THE TANK, STRAINER, PUMP,

BOOM, PRESSURE CONTROL VALVE, AND

NOZZLES, IN YOUR INSPECTION

While continuing to drive the vehicle and

spraying with the monitor in the APPLICATION

RATE position (see FIG 6), turn 1 of the 3 boom

sections off with Individual Boom Valves and

adjust Boom Bypass Valve, if required, to maintain

the application rate from step 3 above. Boom

Bypass Valves are located directly behind the

Individual Boom Valves.

Repeat Step 1 for remaining 2 boom sections

(this allows accurate application rate when

Individual Boom Sections are turned off).

NOTES:

Содержание 41107-210000101

















































































Результаты поиска

Содержание 41107-210000101

Отзывы:

Похожие инструкции для 41107-210000101

Бренды по названию

Популярные бренды

Toro 41107-210000101, Руководство оператора и инструкция по установке

Результаты поиска

Содержание 41107-210000101

Отзывы:

Похожие инструкции для 41107-210000101

Бренды по названию

Популярные бренды