Toro 41107-210000101 Скачать руководство пользователя

Страница: 58 / 80

FILLING THE SOLUTION TANK:

BEFORE SPRAYING

IMPORTANT: Follow the chemical

manufacturer's instructions for mixing spray

solution to obtain desired application rate. Do

not add chemical to Tank until just before use.

The concentrate should not be poured into an

empty Tank: Fill tank about 3/4 full with clean

clear water. With agitation ON, add chemical

concentrate slowly and finish filling Tank with

water.

NOTE:

When using water-soluble bags;

Fill chemical tank 1/2 full of clean, clear water, then

place water-soluble bags in Tank Strainer and use

anti-siphon device to finish filling tank through tank

strainer

DO NOT PLACE WATER-SOLUBLE BAGS

DIRECTLY INTO TANK.

Premix wettable powders in one or two 5-gallon

containers, then slowly add premix to 3/4 tank of

clean clear water with agitation ON.

FILL FRESH WATER WASH TANK (See

FIG. 1):

In case of chemical contact with skin or eyes,

a fresh water wash tank has been installed on

the left side of the vehicle. Refer to the

Chemical Manufacturer's label for instructions

on seeking medical attention.

NOTE: Fill Fresh Water Wash Tank each

day of operation with clean water only.

Check to assure tank is full before each

operation.

CAUTION

CHEMICALS ARE HAZARDOUS AND CAN

CAUSE PERSONAL INJURY!

Carefully read the directions print-

ed on the chemical manufacturer's

labels before handling chemicals.

Instructions on chemical manufac-

turer's container labels, regarding

mixing proportions, should be read

and strictly followed.

Keep spray material away from skin.

If spray material comes in contact

with body, wash it off immediately

with clean water and detergent.

Always wear goggles and other

protective equipment as recommended

by the Chemical Manufacturer.

1. Fresh Water Tank

2. Spigot

Turn Tank Spigot to on position.

Hold contaminated area directly in water

stream. Flush thoroughly.

FIG. 1

1877

Содержание 41107-210000101

















































































Результаты поиска

Содержание 41107-210000101

Отзывы:

Похожие инструкции для 41107-210000101

Бренды по названию

Популярные бренды

Toro 41107-210000101, Руководство оператора и инструкция по установке

Результаты поиска

Содержание 41107-210000101

Отзывы:

Похожие инструкции для 41107-210000101

Бренды по названию

Популярные бренды