background image

      

 

Use and Maintenance Manual 

 A16 J   A18 J Series 

Page 50 

 

5.2.5.

 

User interface display (E) 

 
The multifunction display for machine/user interface is used to display: 

 

the operation parameters of the machine during normal functioning or in the event of a fault; 

 

Working  hours  of  Diesel  engine (when  Diesel  power  is  selected  the  working  hours  are  displayed  in the format  HOURS: 
MINUTES and final letter D). 

 

Working hours of the emergency electric pump with continuous current (when 12V electrical power is selected the working 
hours are displayed in the format HOURS:MINUTES and final letter M) 

OPTIONAL-; 

 

Working hours of the single-phase or three-phase work pump (when 220V or 380V electric power is selected 

at platform- 

the working hours are displayed in the format HOURS:MINUTES and final letter E) 

OPTIONAL-; 

 

Battery charge level (only electrical models E). 

 

 

The user interface display is also used during any interventions by specialized personnel to calibrate/adjust 
the working parameters of the machine. This function is not available to the user. 

 
 

5.2.6.

 

Battery charger warning light (F) 

 
Electric and dual-

powered models (“E”,

 

“ED” and “EB”), equipped with a built

-in high frequency battery charger, are provided 

with this warning light indicating the operation of the battery charger (for more detailed information read the paragraph "Battery 

charge”).

 

 

 

5.2.7.

 

Enabled control panel warning light (G) 

 

The green light is ON when the machine is turned ON and the ground control panel is enabled (the on/off key (C) should be 

kept in “turret” pos

ition). 

 
 

5.2.8.

 

Diesel engine warning lights (H, L, M, N) 

 

These warning lights warn the user of any Diesel engine operational faults (models D and ED). One of these warning lights 

turns ON when the motor is stopped. A “fault” message is sent to the operator on the platform (see paragraph “Platfo

rm control 

panel”)

 

Once the Diesel engine has stopped due to a problem signalled by one of these warning lights, the motor can no longer be re-
started until such problem has been solved. 

 
 

5.2.9.

 

Levers of movement of the platform (O, P, Q, R, S, T, U) 

 

The  various  levers shown  in the figure  allow  the  platform to  be  operated.  According to the  various  signs  the  corresponding 
movements  are  activated.  These  controls  can  be  operated  only  if  the  on-off  key  is  set  to  ON  down  (ground  control  panel 
selected). We shall also remind you that the ground controls are to be used to operate the platform only in emergency situations 

and 

must 

not 

be 

used 

for 

any 

other 

purposes. 

 

Use the ground controls only in emergency situations to allow the platform to be lowered.  

IT IS FORBIDDEN to use the ground control panel as a workstation when personnel is on the platform. 

Содержание AIRO A Series



































































































































Отзывы: