TIGIEFFE AIRO A Series Скачать руководство пользователя страница 5

Страница: 5 / 130

Use and Maintenance Manual

–

A16 J A18 J Series

Page 5

7.2.3.8

Micro-filtration ..................................................................................................................................................... 69

7.2.3.9

Disposal .............................................................................................................................................................. 69

7.2.3.10

Topping up .......................................................................................................................................................... 69

7.2.4.

Hydraulic filter replacement ................................................................................................................................. 70

7.2.4.1.

Suction filters ...................................................................................................................................................... 70

7.2.4.2.

Return filter ......................................................................................................................................................... 70

7.2.5.

Drive reduction gear oil level check and change ................................................................................................... 71

7.2.5.1

Checks in the use of synthetic biodegradable oil in drive reduction gears .............................................................. 71

7.2.6.

Air purging from oscillating axle locking cylinders ................................................................................................. 72

7.2.7.

Telescopic boom sliding blocks clearance adjustment .......................................................................................... 73

7.2.8.

Drive circuit pressure relief valve adjustment and operation check ........................................................................ 74

7.2.9.

Circuit movements pressure relief valve operation check ...................................................................................... 75

7.2.10.

Operation check and adjustment of the braking valves ......................................................................................... 76

7.2.11.

Inclinometer operation check ............................................................................................................................... 77

7.2.12.

Operation check and adjustment of platform overload controller ........................................................................... 79

7.2.13.

Overload controller by-pass

–

ONLY FOR EMERGENCY OPERATIONS ............................................................. 81

7.2.14.

Operation check of M1 microswitches .................................................................................................................. 82

7.2.15.

Dead-man pedal safety system operation check................................................................................................... 82

7.3.

Starter battery ................................................................................................................................................... 83

7.3.1.

tarter battery models “D” “ED”

........................................................................................................................... 83

7.3.2.

Starter type battery for models “E”

....................................................................................................................... 83

7.3.3.

Starter battery maintenance................................................................................................................................. 83

7.3.4.

Starter battery recharge ....................................................................................................................................... 83

7.4.

“DRIVE” battery for models “E” and “ED”

....................................................................................................... 84

7.4.1.

General instructions for DRIVE battery ................................................................................................................. 84

7.4.2.

DRIVE battery maintenance ................................................................................................................................ 84

7.4.3.

DRIVE battery recharge ...................................................................................................................................... 85

7.4.4.

Battery charger: fault report ................................................................................................................................. 86

7.4.5.

Battery replacement ............................................................................................................................................ 86

MARKS AND CERTIFICATIONS .................................................................................................................... 87

PLATES AND STICKERS ............................................................................................................................... 88

10.

CHECK REGISTER ......................................................................................................................................... 90

11.

ELECTRIC DIAGRAMS ................................................................................................................................. 107

12.

HYDRAULIC DIAGRAM ................................................................................................................................ 120

13.

CE CERTIFICATES ....................................................................................................................................... 124

Содержание AIRO A Series



































































































































Результаты поиска

Содержание AIRO A Series

Отзывы:

Похожие инструкции для AIRO A Series

Бренды по названию

Популярные бренды

TIGIEFFE AIRO A Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание AIRO A Series

Отзывы:

Похожие инструкции для AIRO A Series

Бренды по названию

Популярные бренды