Ti Lite AERO Z Скачать руководство пользователя страница 78

Страница: 78 / 147

7-6

Z Series Owners Manual

OM_Z_1212RevC

CHAPTER 7:

BACK UPHOLSTERY, SEAT UPHOLSTERY AND SEAT

CUSHIONS

Seat Cushions

Replacing the Foam Insert in the TiLite Seat Cushion

1. Lift up and remove the existing seat cushion from the seat upholstery.

2. Unzip the seat cushion cover and remove the foam insert.

3. Insert the new foam insert into the seat cushion cover.

4. Close the seat cushion cover and replace on the chair.

For seat cushions manufactured by manufacturers other than TiLite (

e.g. Corbee, StimuLite, Roho, Varilite), consult

the owner’s manual provided by the applicable manufacturer.

Velcro

-Style Adjustable Seat Belt

WARNING

Installation of the Velcro

-Style Seat Belt must be performed by an authorized TiLite dealer or qualified technician.

you ignore this Warning, serious injury may result.

WARNING

The Velcro

-Style Seat Belt must be worn tightly fitted across the lower pelvis or thighs at all times. A loose belt can

allow the user to slip down and create a risk of strangulation. Have your seating specialist demonstrate its proper

adjustment and use. See Figures 7-8 to 7-11. Accidental release of the Velcro

-Style Seat Belt can allow the user to

slip down or fall from the wheelchair. If the user’s movements or cognitive abilities could lead to accidental release,

a caregiver must be present at all times during its use. Ensure that all caregivers know how to unfasten the product.

Failure to do so may delay release in an emergency. As with any new seating support, the Velcro

-Style Seat Belt

may change the way a person sits. Users must continue to practice regular pressure relief activities and skin integrity

checks, not only where this product contacts the user, but also in primary pressure-bearing areas such as the sacrum,

legs, and buttocks. If increased skin redness or irritation occurs, discontinue use and consult your physician or

seating specialist. Failure to do so may result in serious injury, such as pressure ulcers.

If you ignore any of these

Warnings, you may incur serious or life-threatening injuries.

Installation

The seat belt will be installed as shown in Figure 7-8 and 7-10.

Figure 7-8

Aero Z Series 1/ ZR Series 1/ ZRA Series 1

Velcro

-Style Seat Belt with D-Ring

Figure 7-9

Aero Z Series 1/ ZR Series 1/ ZRA Series 1

proper Belt position for Belt with D-Ring

Содержание AERO Z




















































































































































Результаты поиска

Содержание AERO Z

Отзывы:

Бренды по названию

Популярные бренды

Ti Lite AERO Z, Руководство пользователя

Результаты поиска

Содержание AERO Z

Отзывы:

Бренды по названию

Популярные бренды