Ti Lite AERO Z Скачать руководство пользователя страница 54

Страница: 54 / 147

4-12

Z Series Owners Manual

OM_Z_1212RevC

CHAPTER 4: BACKRESTS And PUSH HAndLES

Adjusting the Depth

Tools Needed:

• 7/16” Open End Wrench

• 5/32” Allen Wrench

1. Remove the four Allen screws (two on each side) that secure the back mount to the seat tube. Note the order of

the saddles, washers and nylock nuts. See Figure 4-17.

2. Reposition the back mounts to the desired depth.

3. Reinstall the four Allen screws through the back mount, seat tube, saddles, washers and securely tighten the

nylock nuts.

Note: If your chair has Swing Away Armrests. See Figure 4-18. You may need to use the longer screw provided

with your chair in order to secure both the back mount and the armrest receiver.

WARNING

Any changes to the depth of the backrest will affect the stability (

i.e. center of gravity) of the chair. Use extreme

caution when using a new backrest depth as it may make the chair more prone to tip over. After adjusting the depth

of the backrest, you must consider whether additional changes need to be made to compensate for the modified

stability of the chair (

e.g., changing the rear axle position, backrest angle, rear seat height). If you ignore this

Warning, your chair may not perform properly, which in turn, may cause you to fall, tip over or lose control of the chair

and seriously injure yourself or others or damage the chair.

Figure 4-17

Adjusting the Depth

Figure 4-18

Adjusting the Depth with Swing Away Armrests

Allen

Screws

Allen

Screws

Back

Mount

Back

Mount

Seat

Tube

Seat

Tube

Nylock

Nut

Nylock

Nuts

Washers

Saddles

Receiver

Locking Block

Backrest

Saddle

Bolt-On push Handles

Note: Bolt-On Push Handles should only be used on aluminum backrests.

Mounting

Tools Needed:

• 3/16” Allen Wrench

• 5/32” Allen Wrench

1. See Figure 4-19 for the correct location to mount the Bolt-On Push Handles to the rigidizer bar.

2. Assemble the two halves of the clamp around the rigidizer bar. See Figure 4-20.

3. Using the 3/16” Allen wrench, insert the 1” Allen screw through a washer into the bottom hole on the clamp and

loosely tighten.

4. Insert the push handle into the clamp and align the holes in the push handle with the two upper holes in the

clamp.

Содержание AERO Z




















































































































































Результаты поиска

Содержание AERO Z

Отзывы:

Ti Lite AERO Z, Руководство пользователя, Страница: 54 / 147

Результаты поиска

Содержание AERO Z

Отзывы: