Ti Lite AERO Z Скачать руководство пользователя страница 2

Страница: 2 / 147

WARNING - READ THIS MANUAL

DO NOT OPERATE THIS WHEELCHAIR WITHOUT FIRST READING AND UNDERSTANDING

THIS OWNER’S MANUAL. IF YOU ARE UNABLE TO UNDERSTAND THE WARNINGS,

CAUTIONS AND INSTRUCTIONS, CONTACT YOUR TiLITE DEALER OR TiLITE CUSTOMER

SUPPORT AT (800) 545-2266 BEFORE ATTEMPTING TO USE THIS WHEELCHAIR.

YOU IGNORE THIS WARNING, YOU MAY FALL, TIP OVER OR LOSE CONTROL OF THE

WHEELCHAIR AND SERIOUSLY INJURE YOURSELF OR OTHERS OR DAMAGE THE

WHEELCHAIR.

WARNING - WHEELCHAIR SELECTION

TiLITE MANUFACTURES A WIDE VARIETY OF WHEELCHAIRS TO MEET THE VARIED

NEEDS OF WHEELCHAIR USERS. HOWEVER, TiLITE IS NOT YOUR HEALTH CARE

ADVISOR, AND WE KNOW NOTHING ABOUT YOUR INDIVIDUAL CONDITION OR NEEDS.

THEREFORE, THE FINAL SELECTION OF THE PARTICULAR MODEL, AND HOW IT IS

ADJUSTED, AND THE TYPE OF OPTIONS AND ACCESSORIES NECESSARY REST SOLELY

WITH YOU, THE WHEELCHAIR USER, AND THE HEALTH CARE PROFESSIONAL THAT IS

ADVISING YOU. CHOOSING THE BEST CHAIR AND SETUP FOR YOUR SAFETY DEPENDS

ON SUCH THINGS AS:

1. YOUR DISABILITY, STRENGTH, BALANCE AND COORDINATION;

2. THE TYPES OF HAZARDS YOU MUST OVERCOME IN DAILY USE (WHERE YOU

LIVE AND WORK AND OTHER PLACES YOU ARE LIKELY TO USE YOUR CHAIR); AND

3. YOUR NEED FOR OPTIONS FOR YOUR SAFETY AND COMFORT (SUCH AS ANTI-

TIPS, POSITIONING BELTS OR SPECIAL SEATING SYSTEMS).

IF YOU IGNORE THIS WARNING, YOU MAY ENDANGER YOUR HEALTH.

WARNING - TIE-DOWN RESTRAINTS

TiLITE RECOMMENDS THAT WHEELCHAIR USERS NOT BE TRANSPORTED IN VEHICLES

OF ANY KIND WHILE IN WHEELCHAIRS. AS OF THIS DATE, THE UNITED STATES

DEPARTMENT OF TRANSPORTATION HAS NOT APPROVED ANY TIE-DOWN SYSTEM

FOR TRANSPORTATION OF A USER WHILE IN A WHEELCHAIR IN A MOVING VEHICLE

OF ANY TYPE. IT IS TiLITE’S POSITION THAT USERS OF WHEELCHAIRS SHOULD BE

TRANSFERRED INTO APPROPRIATE VEHICLE SEATING FOR TRANSPORTATION AND

SHOULD USE THE RESTRAINTS MADE AVAILABLE BY THE AUTO INDUSTRY. TiLITE

CANNOT, AND DOES NOT, RECOMMEND ANY WHEELCHAIR TRANSPORTING SYSTEMS.

WARNING - SEATING RESTRAINTS

IT IS THE OBLIGATION OF YOUR DEALER AND THE HEALTH CARE PROFESSIONALS

WHO ARE ADVISING YOU TO DETERMINE IF YOU REqUIRE A SEATING RESTRAINT

OR POSITIONING SYSTEM IN ORDER TO ENSURE THAT YOU CAN SAFELY OPERATE

YOUR WHEELCHAIR. SERIOUS INJURY CAN OCCUR IN THE EVENT OF A FALL FROM A

WHEELCHAIR.

__________________________________________________________________________________________

Note: The information contained in this document is subject to change without notice. An updated version of this

Owner’s Manual may be available at www.tilite.com

__________________________________________________________________________________________

SAVE THIS MANUAL FOR FUTURE REFERENCE

Z Series Owners Manual

OM_Z_1212RevC

Содержание AERO Z




















































































































































Результаты поиска

Содержание AERO Z

Отзывы:

Похожие инструкции для AERO Z

Бренды по названию

Популярные бренды

Ti Lite AERO Z, Руководство пользователя

Результаты поиска

Содержание AERO Z

Отзывы:

Похожие инструкции для AERO Z

Бренды по названию

Популярные бренды