Ti Lite AERO Z Скачать руководство пользователя страница 104

Страница: 104 / 147

11-4

Z Series Owners Manual

OM_Z_1212RevC

CHAPTER 11: CASTERS, FORKS AND CASTER PIN LOCKS

Figure 11-6

ZR Series 2 Single-Sided Fork

Caster Cap

Washer

Nylock Nut

Caster

Caster Cap

Allen

Screw

Mono Fork

Fork Stem

Figure 11-7

Slipstream Single-Sided Fork

Fork Stem

Mono Fork

Caster Cap

Washer

Nylock Nut

Caster

Caster Cap

Allen

Screw

Replacing Forks

Tools Needed:

• 9/16” Wrench

• 1/8” Allen Wrench

1. Remove the casters. See “Slipstream Single-Sided Forks - Replacing Casters” on page 11-3.

2. Remove the nylock nut and washer that secure the fork to the fork stem. See Figures 11-6 and 11-7.

3. Remove the old fork and install the replacement fork on the fork stem.

4. Replace the nylock nut and washer and securely tighten.

5. Reinstall the casters. See “Slipstream Single-Sided Forks - Replacing Casters” on page 11-3.

WARNING

On the ZR Series, the fork stem is permanently installed in the “Bullet” Caster Housing. Do not attempt to unscrew

the fork stem or the set screw. If it should become necessary to replace the fork stem on these chairs, this repair

can only be performed by TiLite at our factory.

If you ignore this Warning, you may fall, tip over or lose control of the

wheelchair and seriously injure yourself or others or damage the wheelchair.

Caster pin Locks

(Aero Z Series 1, ZR Series 1, ZRA Series 1)

WARNING

ALWAYS be sure to disengage both Caster Pin Locks before attempting to propel your chair.

If you ignore this

Warning, you may fall, tip over or lose control of the wheelchair and seriously injure yourself or others or damage the

wheelchair.

To engage the Caster Pin Locks:

1. Rotate the caster until either notch on the lock ring is directly beneath the T-Handle. See Figure 11-8.

2. Lift, rotate and lower the T-handle down into the lower notch on the Caster Pin Lock. See Figure 11-9.

3. Make sure the pin lock is fully engaged in one of the notches in the lock ring.

To disengage the Caster Pin Lock, lift, rotate and lower the T-Handle down into the upper notch on the Caster Pin

Lock. See Figure 11-8.

Содержание AERO Z




















































































































































Результаты поиска

Содержание AERO Z

Отзывы:

Похожие инструкции для AERO Z

Бренды по названию

Популярные бренды

Ti Lite AERO Z, Руководство пользователя

Результаты поиска

Содержание AERO Z

Отзывы:

Похожие инструкции для AERO Z

Бренды по названию

Популярные бренды