Ti Lite AERO Z Скачать руководство пользователя страница 47

Страница: 47 / 147

4-5

Z Series Owners Manual

OM_Z_1212RevC

CHAPTER 4: BACKRESTS And PUSH HAndLES

backrest posts with the holes in the backrest.

4. Make sure both backrest posts are at the same height in the backrest and reinsert and securely tighten the two

Allen screws.

5. Reinstall the backrest pad and adjust the upholstery to the desired tautness. See “Velcro

-Style Adjustable Back

Upholstery” or “Tension Adjustable by Straps Back Upholstery” on pages 7-1 to 7-3.

Figure 4-8

Adjusting the Backrest Height

Backrest

Integrated Push

Handle (optional)

Allen Screws

Backrest

Post

WARNING

The threads on the Allen screws that secure the backrest posts to the backrest have been treated with a Vibra-TITE

VC-3, a locking and sealing coating, to reduce the possibility that they will become loose. You should be able to

adjust the backrest height approximately four times without reapplying thread lock to these screws. TiLite requires that

you reapply Vibra-TITE

VC-3 after every fourth adjustment.

If you ignore this Warning, your backrest posts could

become loose or disconnected from the wheelchair, and you could fall, tip over or lose control of the wheelchair and

seriously injure yourself or others or damage the wheelchair.

Note: If your backrest is set to 8-½”, 9”, or 9-½” and you need to adjust the backrest height, the following procedure

applies:

1. Remove the backrest upholstery. See “Velcro

-Style Adjustable Back Upholstery” or “Tension Adjustable by

Straps Back Upholstery” on pages 7-1 to 7-3.

2. If your backrest is set to 8-½” and if you are setting the backrest at 9” or 9-½”:

a. Remove the backrest from the backrest brackets. See “Replacing the Backrest” on page 4-10.

b. Remove the top end caps. See Figure 4-9.

c. If the backrest is titanium, remove the long end plugs (see Figure 4-9) and install the short end plugs.

If the backrest is aluminum, skip to Step 2.d.

d. Install the backrest sleeve in each backrest tube. See Figure 4-9.

e. Remove the threaded post plugs from the bottom end of the backrest posts (see Figure 4-9) and

insert the backrest posts into the backrest.

f. Align the backrest posts inside the backrest so that the desired hole in the backrest post aligns with

the second lowest hole in the backrest. See Figure 4-10.

g. Secure the backrest posts inside the backrest and the backrest to the bracket using the Allen screws

and locknuts. Note that the Allen screws used to secure the backrest posts inside the backrest will

also serve to secure the backrest to the brackets. See Figure 4-10. See “Replacing the Backrest” on

page 4-10. Proceed to Step 7.

Содержание AERO Z




















































































































































Результаты поиска

Содержание AERO Z

Отзывы:

Бренды по названию

Популярные бренды

Ti Lite AERO Z, Руководство пользователя

Результаты поиска

Содержание AERO Z

Отзывы:

Бренды по названию

Популярные бренды