Ti Lite AERO Z Скачать руководство пользователя страница 130

Страница: 130 / 147

13-10

Z Series Owners Manual

OM_Z_1212RevC

CHAPTER 13: ANTI-TIPS

Adjusting

To adjust the height of the User-Friendly Anti-Tip, press the two release buttons on the telescoping lower tube and

adjust the height of the lower tube so that the wheel is within 1-1/2” to 2” off the ground. See Figure 13-14.

Figure 13-14

Adjusting the Anti-Tip

Anti-Tip

Mount

Release Button

Receiver

Upper Tube

Lower Tube

Release Button

Removing

To remove the User-Friendly Anti-Tip tube, press the two release buttons in the anti-tip receiver and pull the upper

tube out of the anti-tip receiver. See Figure 13-14.

Mounting

WARNING

Only an authorized TiLite dealer or qualified technician should install the anti-tip receiver.

If you ignore this Warning,

you may fall, tip over or lose control of the wheelchair and seriously injure yourself or others or damage the

wheelchair.

WARNING

Do not disassemble the anti-tip mounting assembly. See Figure 13-15 and 13-16.

If you ignore this Warning, you

may fall, tip over or lose control of the wheelchair and seriously injure yourself or others or damage the wheelchair.

Tools Needed:

• 5/32” Allen Wrench

• 3/16” Allen Wrench

• 5/64” Allen Wrench

1. Remove the rear wheels and place the frame upside down on a level surface.

2. Remove the camber tube. See “Replacing the Camber Tube (ZR Series 2)” on pages 8-7 and 8-8 or “Replacing

the Camber Tube (Aero Z Series 2 and ZRA Series 2)” on page 8-4.

3. Thread the Allen screw through the right side camber tube clamp and into the right side anti-tip mount using the

center of the three threaded holes and loosely tighten. See Figures 13-15 and 13-16.

4. Repeat Step 3 with the left side camber tube clamp and the left side anti-tip mount.

5. Reinstall the camber tube. See “Replacing the Camber Tube (ZR Series 2)” on pages 8-7 and 8-8 or “Replacing

the Camber Tube (Aero Z Series 2 and ZRA Series 2)” on page 8-4. The bumper cannot be reinstalled.

Содержание AERO Z




















































































































































Результаты поиска

Содержание AERO Z

Отзывы:

Ti Lite AERO Z, Руководство пользователя, Страница: 130 / 147

Результаты поиска

Содержание AERO Z

Отзывы: