Ti Lite AERO Z Скачать руководство пользователя страница 64

Страница: 64 / 147

5-8

Z Series Owners Manual

OM_Z_1212RevC

CHAPTER 5: ARMRESTS

WARNING

Make sure that the stop clamp is securely tightened before applying weight to the armrest.

If you ignore this Warning,

you could fall, tip over or lose control of the wheelchair and seriously injure yourself or others or damage the

wheelchair.

Figure 5-15

Adjusting Armrest Angle

Stop Clamp

Allen Screw

Locking the Armrest in place

Tools Needed:

• 3/16” Allen Screw

• 7/16” End Wrench

1. To lock the armrest in place after the armrest is seated in the receiver in the desired position, insert the locking

screw through the armrest receiver and the armrest. See Figure 5-16.

2. Securely tighten the locknut to the locking screw.

Note: TiLite wheelchairs do not ship with locking screws and nuts. If you require the locking screws and nuts, please

contact TiLite Customer Service at 1-800-545-2266.

Note: Locking the armrest in place only prevents the armrest from swinging away. The armrest will still flip back.

Note: Depending on the configuration of your chair (including rear wheel height and armrest height) it may not be

possible to lock the armrest in place.

Figure 5-16

Locking the Armrest in place

Locknut

Locking

Screw

Receiver

Swing Away Flip-Back Armrest

(Aero Z Series 2, ZR Series 2, ZRA Series 2)

To flip back the armrest, raise the front of the armrest and rotate it straight back as far as possible. Reverse this

procedure to return the armrest to its original position. See Figure 5-17.

To swing away the armrest, lightly lift up on the armrest and rotate the armrest away from the chair. See Figure 5-17.

To replace the armrest, swing it back towards the chair and gently push it back down into place.

Содержание AERO Z




















































































































































Результаты поиска

Содержание AERO Z

Отзывы:

Похожие инструкции для AERO Z

Бренды по названию

Популярные бренды

Ti Lite AERO Z, Руководство пользователя

Результаты поиска

Содержание AERO Z

Отзывы:

Похожие инструкции для AERO Z

Бренды по названию

Популярные бренды