Ti Lite AERO Z Скачать руководство пользователя страница 44

Страница: 44 / 147

4-2

Z Series Owners Manual

OM_Z_1212RevC

CHAPTER 4: BACKRESTS And PUSH HAndLES

Adjusting the Backrest Lock Bracket

(Aero Z Series 1, ZR Series 1, ZRA Series 1)

Tools Needed:

• 3/16” Allen Wrench

• 1/2” Open End Wrench

If the backrest will not lock in the unfolded (upright) position,

follow these procedures:

1. Fold the backrest down over the seat.

2. Place the 1/2” Open End Wrench on the locknut on the

inner side of the seat rail, which holds the latch screw in

place. Using the 3/16” Allen wrench, loosen, but do not

remove, the latch screw. See Figure 4-3.

3. Rotate the latch spacer.

4. Securely tighten the latch screw.

5. If the backrest still will not lock securely in the unfolded

position, repeat the procedure on the opposite side of

the chair.

Note: Do not over tighten the latch screw or you may

damage the latch spacer.

Adjusting if there is “play” in the Backrest or Backrest Bracket

(Aero Z Series 1, ZR Series 1, ZRA Series 1)

Tools Needed:

• 7/16” Open End Wrench

• 5/32” Allen Wrench

If the backrest or backrest bracket becomes loose or there

is “play” in the folding backrest assembly, follow these

procedures:

1. On each side of the chair, tighten both Allen screws

and the pivot screw shown in Figure 4-4.

2. Repeat this procedure until there is no “play” in the

folding backrest assembly.

3. Do not over tighten the pivot screw or the backrest will

not fold/unfold.

Note: If the above procedure does not completely eliminate the “play” in the backrest, tighten the latch screw. Do not

overtighten the latch screw or you may damage the latch spacer. See Figure 4-3.

Adjusting the Back Mount

(Aero Z Series 2, ZR Series 2, ZRA Series 2)

Tools Needed:

• Two 7/16” Open End Wrenches

If your backrest is difficult to fold and unfold or is too loose, follow these procedures:

1. Using an Open End wrench, hold the pivot bolt in place and slightly loosen or tighten the nylock nut with the

second Open End wrench. See Figure 4-5.

2. Repeat the procedure on each side of the chair until the desired tightness is achieved.

Figure 4-4

Adjusting the Backrest Bracket

Backrest

Pivot Screw

Allen Screw

Latch

Screw

Figure 4-3

Adjusting the Backrest Lock Bracket

Latch

Spacer
Latch

Screw

Содержание AERO Z




















































































































































Результаты поиска

Содержание AERO Z

Отзывы:

Бренды по названию

Популярные бренды

Ti Lite AERO Z, Руководство пользователя

Результаты поиска

Содержание AERO Z

Отзывы:

Бренды по названию

Популярные бренды