Ti Lite AERO Z Скачать руководство пользователя страница 38

Страница: 38 / 147

3-4

Z Series Owners Manual

OM_Z_1212RevC

CHAPTER 3: FOOTRESTS

WARNING

The threads on the Allen screws that secure the T-Nuts within the footrest clamp assembly are treated with Vibra-

TITE

VC-3, a locking and sealing coating. You should be able to adjust the height of the footrest approximately four

times without reapplying the coating. TiLite requires that you reapply Vibra-TITE

VC-3 after every fourth adjustment.

If you ignore this Warning, your footrest could become loose or fall off and you could fall, tip over or lose control of the

wheelchair and seriously injure yourself or others or damage the wheelchair.

Titanium Open Loop Footrest

(ZR Series)

The Titanium Open Loop Footrest (see Figure 3-6) can be replaced, or the height adjusted, by using the tools and

following the procedures under “Titanium Footrest with Flat ABS Cover (ZR Series and ZRA Series)” on page 3-2.

Figure 3-6

Titanium Open Loop Footrest

(Aero Z Series)

The Titanium Open Loop Footrest (see Figure 3-6) can be replaced or the height adjusted by using the tools and
following the procedures under “Titanium Footrest with Flat ABS Cover (Aero Z Series)” on page 3-3.

Angle Adjustable Footrest

Adjusting the Angle

Tools needed:

• 5/32” Allen Wrench

1. Loosen, but do not remove, the two Allen screws that secure the footplate to the clamp. See Figure 3-7.

2. Adjust the footrest to desired angle.

3. Tighten the Allen screws, making sure the screws and the locknuts are secure and will not permit the footplate to

move up or down under weight.

Figure 3-7

Adjusting the Angle

Allen

Screws

Footplate

Clamp

Washers

Locknuts

Содержание AERO Z




















































































































































Результаты поиска

Содержание AERO Z

Отзывы:

Похожие инструкции для AERO Z

Бренды по названию

Популярные бренды

Ti Lite AERO Z, Руководство пользователя

Результаты поиска

Содержание AERO Z

Отзывы:

Похожие инструкции для AERO Z

Бренды по названию

Популярные бренды