Ti Lite AERO Z Скачать руководство пользователя страница 127

Страница: 127 / 147

13-7

Z Series Owners Manual

OM_Z_1212RevC

CHAPTER 13: ANTI-TIPS

Figure 13-10

Mounting the User-Friendly Rear Flip-Up Anti-Tips

on the Aero Z Series 1 and ZRA Series 1

Camber

Tube

Camber Tube

Mount

Allen

Screw

Allen

Screws

NyLock Nuts

Mounting Plate

WARNING

TiLite Logo Must Face
Rearward and Arrows

on All Anti-Tipper

Components Must Align.

Mounting

(ZR Series 1)

WARNING

Only an authorized TiLite dealer or qualified technician should install the rear anti-tip receiver.

If you ignore this

Warning, you may fall, tip over or lose control of the wheelchair and seriously injure yourself or others or damage the

wheelchair.

WARNING

Do not disassemble the anti-tip mounting assembly. See Figure 13-11.

If you ignore this Warning, you may fall, tip

over or lose control of the wheelchair and seriously injure yourself or others or damage the wheelchair.

Note: Unless you ordered User Friendly Rear Flip-Up Anti-tips when you ordered your ZR Series 1 wheelchair, you

will need to order replacement Allen screws and new locknuts when ordering User Friendly Rear Flip-Up Anti-Tips.

Tools Needed:

• 5/32” Allen Wrench

1. Remove the rear wheels and place the frame upside down on a level surface.

2. Remove the camber tube. See “Replacing the Camber Tube (ZR Series 1)” on page 8-6.

3. Remove one of the two Allen screws and lock washers that secure the right camber clamp to the right CG

bracket.

4. Align the anti-tip mounting plate with the right CG bracket as shown in Figure 13-11. Thread the new, longer Allen

screw through the right camber clamp, the right CG bracket and the anti-tip mounting plate and secure with the

new locknut. You will not need the lock washer. Make sure to utilize the same threaded hole in the CG bracket

that you were using prior to removing the Allen screw in Step 3. Do not disassemble the anti-tip mounting plate

from the anti-tip receiver.

5. Remove the second Allen screw and lock washer that secures the right camber clamp to the right CG bracket.

6. Thread the second, longer Allen screw through the right camber clamp, the right CG bracket and the anti-tip

mounting plate and secure with the new locknut. You will not need the lock washer. Make sure to utilize the

same threaded hole in the CG bracket that you were using prior to removing the Allen screw in Step 5. Do not

disassemble the anti-tip mounting plate from the anti-tip receiver.

7. Repeat Steps 3 through 6 on the left side of the chair.

8. Reinstall the camber tube as shown in Figure 13-11 and see “Replacing the Camber Tube (ZR Series 1)” on page

8-6.

Содержание AERO Z




















































































































































Результаты поиска

Содержание AERO Z

Отзывы:

Ti Lite AERO Z, Руководство пользователя, Страница: 127 / 147

Результаты поиска

Содержание AERO Z

Отзывы: