Thermo Scientific AQUAfast AQ3700 Скачать руководство пользователя

Страница: 204 / 264

202

Thermo Scientific Orion AQUAfast AQ3700 Colorimeter User Guide

Correct filling of the vial:

6. Always perform zeroing and test with closed vial cap.
7. Bubbles on the inside wall of the vial lead to incorrect measurements. To prevent this,

remove the bubbles by swirling the vial before performing the test.

8. Avoid spillage of water in the sample chamber. If water should leak into the instrument

housing, it can destroy electronic components and cause corrosion.

9. Contamination of the lens in the sample chamber can result in errors. Check at regular

intervals and – if necessary – clean the light entry surfaces of the sample chamber using

a moist cloth or cotton buds.

10. Large temperature differences between the instrument and the environment can lead

to errors – e.g. due to the formation of condensation in the area of the lens or on

the vial.

11. To avoid errors caused by stray light do not use the instrument in bright sunlight.

Insertion of the adapter:

adapter 16 mm Ø

adapter 13 mm Ø

Содержание AQUAfast AQ3700









































































































































































































































































Результаты поиска

Содержание AQUAfast AQ3700

Отзывы:

Похожие инструкции для AQUAfast AQ3700

Бренды по названию

Популярные бренды

Thermo Scientific AQUAfast AQ3700, Руководство пользователя

Результаты поиска

Содержание AQUAfast AQ3700

Отзывы:

Похожие инструкции для AQUAfast AQ3700

Бренды по названию

Популярные бренды