Thermo Scientific AQUAfast AQ3700 Скачать руководство пользователя

Страница: 237 / 264

Thermo Scientific Orion AQUAfast AQ3700 Colorimeter User Guide

Store user calibration

Perform the required method as described in the manual
using a standard of known concentration instead of the
water sample.

If the test result is displayed press [MODE], [Shift] + [4] [5]
keys and confirm with [ ] key.

The display shows:

Pressing the arrow key [ ] once increases the displayed
result.

Pressing the arrow key [ ] once decreases the displayed
result.

Press keys till the displayed result corresponds to the value
of the standard.

Confirm with [ ] key to store the new calibration factor.
Cancel user calibration by pressing [ESC] key.

The display shows:

Now the method name is displayed inverse and the test result
is calculated with the new calibration factor.

100 Chlorine T
0.02-6 mg/l Cl2
0.90 mg/l free Cl2

<user calibration>
100 Chlorine T
0.02-6 mg/l Cl2
0.90 mg/l free Cl2
up: , down:
save:

Jus Factor
saved

100

Chlorine T

0.02-6 mg/l Cl2
1.00 mg/l free Cl2

No.

Method

Recommended range

for user calibration

351

Silica LR PP

1 mg/l SiO

352

Silica HR PP

50 mg/l SiO

212

Sodium hypochlorite

8 %

360

Sulfate PP

50 mg/l SO

355

Sulfate T

50 mg/l SO

365

Sulfide

0.2-0.4 mg/l S

370

Sulfite

3-4 mg/l SO

390

Urea

1-2 mg/l CH

400

Zinc

0.2-0.4 mg/L Zn

Mode

Содержание AQUAfast AQ3700









































































































































































































































































Результаты поиска

Содержание AQUAfast AQ3700

Отзывы:

Похожие инструкции для AQUAfast AQ3700

Бренды по названию

Популярные бренды

Thermo Scientific AQUAfast AQ3700, Руководство пользователя

Результаты поиска

Содержание AQUAfast AQ3700

Отзывы:

Похожие инструкции для AQUAfast AQ3700

Бренды по названию

Популярные бренды