Thermo Scientific AQUAfast AQ3700 Скачать руководство пользователя | Manualshive

Страница: 43 / 264

background image

Thermo Scientific Orion AQUAfast AQ3700 Colorimeter User Guide

1.1 Methods

Notes:

1. Vial cleaning:
  As many household cleaners (e.g. dishwasher detergent) contain reducing substances,
  the subsequent determination of Chlorine may show lower results. To avoid any
  measurement errors, only use glassware free of Chlorine demand.
  Preparation: Put all applicable glassware into Sodium hypochlorite solution (0.1 g/l) for
  one hour, then rinse all glassware thoroughly with deionized water.
2. For individual testing of free and total Chlorine, the use of different sets of glassware is
  recommended (EN ISO 7393-2, 5.3)
3. Preparing the sample:
  When preparing the sample, the escape of Chlorine gases, e.g. by pipetting or shaking,
  must be avoided. The analysis must take place immediately after taking the sample.
4. The DPD color development is carried out at a pH value of 6.2 to 6.5. The reagents
  therefore contain a buffer for the pH adjustment.
  Strong alkaline or acidic water samples must be adjusted between pH 6 and pH 7
  before the reagent is added (use 0.5 mol/l Sulfuric acid resp. 1 mol/l Sodium hydroxide).
5. Exceeding the measuring range:
  Concentrations above:
  10 mg/l Chlorine using tablets
    4 mg/l Chlorine using liquid reagents
    2 mg/l using powder packs
   can lead to results showing 0 mg/l. In this event, the water sample must be diluted with
  water free of Chlorine. 10 ml of the diluted sample should be mixed with the reagent
  and the measurement repeated.
6. Turbidity (can lead to errors):
  The use of the DPD No. 1 tablet (method 100) in samples with high Calcium ion
  contents* and/or high conductivity* can lead to turbidity of the sample and therefore
  incorrect measurements. In this event, the reagent tablet DPD No. 1 High Calcium
  should be used as an alternative. Even if turbidity does occur after the DPD No. 3
  tablet has been added, this can be prevented by using the DPD No. 1 HIGH CALCIUM
  tablet.

* it is not possible to give exact values, because the development of turbidity

depends on the nature of the sample.

7. If ??? is displayed at a differentiated test result see page 242.

Oxidizing agents such as Bromine, Ozone etc. interfere as they react in the same way as
Chlorine.

«
...
41
42
43
44
45
...
»

Содержание AQUAfast AQ3700









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AQUAfast AQ3700

Бренд: PAT Страницы: 55

Бренд: PAT Страницы: 31

Бренд: Keithley Страницы: 73

Бренд: Tascam Страницы: 4

Бренд: Harpers Страницы: 8

Бренд: Oakton Страницы: 16

GroundCast DRS611

Бренд: Vaisala Страницы: 12

Бренд: ISKRAEMECO Страницы: 12

RAVTD1760WS Series

Бренд: Ravaglioli Страницы: 24

Бренд: Aethra Страницы: 2

Бренд: Flymaster Страницы: 7

RLACS277RLACS29

Бренд: Racelogic Страницы: 10

Бренд: A&D Страницы: 2

Бренд: Rinstrum Страницы: 2

BlueForce Smart

Бренд: CAME Страницы: 24

Бренд: BC Biomedical Страницы: 9

MLS 50-3...N series

Бренд: KERN Страницы: 16

Бренд: Fora Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды