Thermo Scientific AQUAfast AQ3700 Скачать руководство пользователя

Страница: 112 / 264

Thermo Scientific Orion AQUAfast AQ3700 Colorimeter User Guide

1.1 Methods

Iron, total (TPTZ, Note 1)

with Powder Pack

0.02 – 1.8 mg/l Fe

Use two clean vials (24 mm Ø) and mark one as blank for
zeroing.

1. Fill a clean vial with

10 ml deionized water

(this is the

blank).

2. Fill the second clean vial with

10 ml of the water

sample

(this is the sample).

3. Add the contents of

one IRON TPTZ F10 Powder

Pack

straight from the foil into each vial.

4. Close the vials tightly with the caps and swirl several

times to mix the contents.

5. Press

[ ]

key.

Wait for a reaction

period of 3 minutes.

After the reaction period is finished proceed as follows:

6. Place the vial (the blank) in the sample chamber making

sure that the marks are aligned.

7. Press

ZERO

key.

8. Remove the vial from the sample chamber.

9. Place the vial (the sample) in the sample chamber ma-

king sure that the marks are aligned.

10. Press

TEST

key.

The result is shown in the display in mg/l Iron.

prepare Zero
press ZERO

Zero accepted
prepare Test
press TEST

Countdown
3:00
start:

Содержание AQUAfast AQ3700









































































































































































































































































Результаты поиска

Содержание AQUAfast AQ3700

Отзывы:

Похожие инструкции для AQUAfast AQ3700

Бренды по названию

Популярные бренды

Thermo Scientific AQUAfast AQ3700, Руководство пользователя

Результаты поиска

Содержание AQUAfast AQ3700

Отзывы:

Похожие инструкции для AQUAfast AQ3700

Бренды по названию

Популярные бренды