Thermo Scientific AQUAfast AQ3700 Скачать руководство пользователя

Страница: 24 / 264

Thermo Scientific Orion AQUAfast AQ3700 Colorimeter User Guide

1.1 Methods

Ammonia

with Tablet

0.02 – 1 mg/l N

1. Fill a clean vial (24 mm Ø) with

10 ml of the water

sample,

close tightly with the cap.

2. Place the vial in the sample chamber making sure that

the marks are aligned.

3. Press

ZERO

key.

4. Remove the vial from the sample chamber.

5. Add

one AMMONIA No. 1 tablet

straight from the foil

to the water sample and crush the tablet using a clean

stirring rod.

6. Add

one AMMONIA No. 2 tablet

straight from the foil

to the same water sample and crush the tablet using a

clean stirring rod.

7. Close the vial tightly with the cap and swirl several times

until the tablets are dissolved.

8. Place the vial in the sample chamber making sure that

the marks are aligned.

9. Press

TEST

key.

Wait for a

reaction period of 10 minutes.

After the reaction period is finished the measurement

starts automatically.

The result is shown in the display in mg/l Ammonia as N.

prepare Zero
press ZERO

Zero accepted
prepare Test
press TEST

Countdown
10:00

Содержание AQUAfast AQ3700









































































































































































































































































Результаты поиска

Содержание AQUAfast AQ3700

Отзывы:

Похожие инструкции для AQUAfast AQ3700

Бренды по названию

Популярные бренды

Thermo Scientific AQUAfast AQ3700, Руководство пользователя

Результаты поиска

Содержание AQUAfast AQ3700

Отзывы:

Похожие инструкции для AQUAfast AQ3700

Бренды по названию

Популярные бренды