Thermo Scientific AQUAfast AQ3700 Скачать руководство пользователя

Страница: 122 / 264

Thermo Scientific Orion AQUAfast AQ3700 Colorimeter User Guide

1.1 Methods

Molybdate / Molybdenum HR

with Powder Pack

0.5 – 66 mg/l MoO

/ 0.3 – 40 mg/l Mo

1. Fill a clean vial (24 mm Ø) with

10 ml of the water

sample

, close tightly with the cap.

2. Place the vial in the sample chamber making sure that

the marks are aligned.

3. Press

ZERO

key.

4. Remove the vial from the sample chamber.

5. Add the contents of

one Molybdenum HR 1 F10

Powder Pack

straight from the foil to the water

sample.

6. Close the vial tightly with the cap and swirl several times

to mix the contents.

7. Add the contents of

one Molybdenum HR 2 F10

Powder Pack

straight from the foil to the same water

sample.

8. Close the vial tightly with the cap and swirl several times

to mix the contents.

9. Add the contents of

one Molybdenum HR 3 F10

Powder Pack

straight from the foil to the same water

sample.

10. Close the vial tightly with the cap and swirl several times

to mix the contents.

11. Place the vial in the sample chamber making sure that

the marks are aligned.

12. Press

TEST

key.

Wait for a

reaction period of 5 minutes

After the reaction period is finished the measurement
starts automatically.

The result is shown in the display in mg/l
Molybdate / Molybdenum.

prepare Zero
press ZERO

Zero accepted
prepare Test
press TEST

Countdown
5:00

Содержание AQUAfast AQ3700









































































































































































































































































Результаты поиска

Содержание AQUAfast AQ3700

Отзывы:

Похожие инструкции для AQUAfast AQ3700

Бренды по названию

Популярные бренды

Thermo Scientific AQUAfast AQ3700, Руководство пользователя

Результаты поиска

Содержание AQUAfast AQ3700

Отзывы:

Похожие инструкции для AQUAfast AQ3700

Бренды по названию

Популярные бренды