Installation
Premier Elite Series Installation Manual
12
INS176-15
Premier Elite 12-W, 24-W & 48/64-W PCB Layout (48/64-W Shown)
1: Battery Connections
A 12V rechargeable battery must be connected to these terminals in
order to provide continuous system operation in the event of an AC
Mains failure. (protected by 1.6 Amp PTC Fuse)
2: Digicom Power & Inputs
These terminals provide un-fused power; remote reset and line fault
inputs and are normally used for connecting a stand-alone
communicator to the control panel.
3: Digicom Outputs
Outputs 1 to 8 are low current (100mA ‘
-
ve’ applied) and would
normally be used when connecting a stand-alone communicator to
the control panel. Each output is fully programmable. (1-3 only on 12-
W)
4: Engineers Keypad
A portable Engineers keypad can be plugged on here to allow easier
access for programming and testing.
When using a keypad as an Engineers keypad, the address
mu
st be set to ‘10’. The keypad zones and lid tamper
are not monitored.
5: Network Data Connections
Network 1 provides connection for the keypads and zone expanders.
The ‘+’ and ‘–’ terminals provide power whilst the ‘T’ transmits data
and ‘R’ receives data.
6: Network Data Indicators
The red LED indicates that data is flowing out of the control panel
and normally flashes very quickly. The green LED indicates that data
is flowing into the control panel and normally flashes slowly, the
green LED flashes faster as more devices are connected.
7: Communication Ports
Com Port 1
is a serial communications port and can be used for
connecting a PC running
Wintex
or any supported serial device to the
control panel.
Com Port 2
is a serial communications port and can be used for
connecting a PC running
Wintex
or any supported serial device to the
control panel.
8: Auxiliary 12V Power
These terminals are for connecting devices that require 12V power
(protected by a 0.9A PTC fuse).
9: Expansion
The Expansion Port can be used for connecting a
60XiD
Zone
Expander (see page 33 for details) or an AV Module (see page 42 for
details), X-10 Module (Obsolete), Speech Module or a Memory
Module.
10: External Sounder Connections
These terminals are used for connecting to an external sounder unit.
11: Load Defaults Button
Press and hold this button whilst applying power to the control panel
to load the factory default settings. Close the tamper on the control
panel and then press and hold this button for 7 seconds with power
already on the panel to restore just the Engineer code to the factory
setting of
1234
. See page 53 for full details.
Loading the factory defaults can take up to 30 seconds to
complete.
Loading defaults will only be possible if the NVM has not been
locked.
For a complete list of factory defaults, see the
Quick Reference
Guide
supplied on the enclosed CD.
12: Auxiliary/Fault Connections
These terminals can be used for monitoring the tamper loop of an
auxiliary device (see page 34 for details).
13: Loudspeaker Connections
These terminals can be used for connecting up to one 8
or two
16
loudspeakers.
14: Panel Outputs
Outputs 1 & 2 are 500mA ‘
-
ve’. These outputs are a
ll fully
programmable. (12-W & 24-W only output 1)
15: Zone Connections
4 Fully programmable zone inputs
16:
Ricochet
Network LED’s
Green LED = Data received by the expander from the panel Red LED
= Data transmitted by the expander to the panel.
(The flash rate
depends on the mode and RF activity)
17: Enable 2 wire smoke
Panel Output 1 can be used for connecting up to 10, 12V 2-Wire
smoke detectors.(not 12-W)
18: Options Switch
Use to select the receiver functionality.
Switch 1 OFF =not used on 48-W.
Switch 2 OFF = 24-W & 48-W
Ricochet
Mode
ON = Not Used
1
2
3
5
8
10
12
13
14
22
18
21
7
15
20
19
23
24
25
26
27
29
30
33
31
Engineer REM
OPTIONS
Tamper
Disable
100 V
m = 1 Amp
V
F3
F4
F5
F6
F1
F8
Batt Charge
0.75A 0.3A
F2
!
BAR CODE
USE WITH
TEXECOM PSU
ONLY
F7
32
6
16
11
4
17
28
