Televes OLT 769401 Скачать руководство пользователя страница 395

Страница: 395 / 482

395

/cli/remote-eq/onu/voip> config ?

Usage:

CONFIG

Configure a remote ONU VoIP interface

--onu-voip-port

Identifies the VoIP port to be configured. (e.g voip.1)

[OPTIONAL]

--admin

Administrative State. Enable/disable, in this context.

(enable|disable)

--client-ip

VoIP client IP address. If the value is 0.0.0.0, the IP

address will be

obtained by DHCP.

--ftp-passwd

User password to login in the FTP server to get the XML

file with the VoIP client configuration

--ftp-username

User name to login in the FTP server to get the XML file

with the VoIP client configuration

--hold-over-time

Time during which POTS loop voltage is held up when the

ONU is not

ranged on the GPON.

--ip-mask

IP Network Mask.

--onuID

Identifies an ONU by ID, in this context.

--port

Identifies an interface on the OLT. (e.g.: pon.2; eth.3;

lag.1)

--remote-file

This is the .xml file that contains the client

configuration (e.g. supported codecs, number, etc)

--rx-gain

Specifies the receiver gain (dB) (-12..6)

--specific-profile

Identifies a VoIP specific profile by ID (manage profiles in

‘/profiles/voip/specific-profiles/’ node)

--termination-id

Used for MEGACO(H.248) to identify the line termination

--tx-gain

Specifies the transmitter gain (dB) (-12..6)

--voip-profile

Identifies a VoIP profile by ID (manage profiles in ‘/

profiles/voip/’ node)

Figure 7-460: CLI on line help on “config” command usage in this node context

7.6.17.6.11.2 “show” command

Name

show

Description

Show the current configuration

Full path

/remote-eq/onu/voip/show

Mandatory Parameters

Screen Output

Table, Figure 7-462. Table parameters description inTable 7-422.

Table 7-:421 “show” command information

/cli/remote-eq/onu/voip> show ?

Usage:

SHOW Show the current VoIP interface configuration.

[OPTIONAL]

--onu-voip-port Identifies the VoIP port to be configured. (e.g. voip.1)

--onuID

Identifies an ONU by ID, in this context.

--port

Identifies an interface on the OLT. (e.g.: pon.2; eth.3; lag.1)

Figure 7-461: CLI on line help on “show” command usage in this node context

Содержание OLT 769401



































































































































































































































































































































































































































































































Результаты поиска

Содержание OLT 769401

Отзывы:

Похожие инструкции для OLT 769401

Бренды по названию

Популярные бренды

Televes OLT 769401, Руководство пользователя

Результаты поиска

Содержание OLT 769401

Отзывы:

Похожие инструкции для OLT 769401

Бренды по названию

Популярные бренды