Tandberg Data SLR AUTOLOADER - SERVICE AND Скачать руководство пользователя страница 63

Страница: 63 / 92

SCSI Error Codes

FSC

Display Message

Description

Source of Failure

Suggested Action

1001

SCSI Firmware Error

SCSI Process
detected an
unexpected error
condition.

Robotics Assembly

1002

SCSI FIFO Empty

SCSI Controller FIFO
is empty.

1003

SCSI FIFO Error

SCSI Controller FIFO
should be empty.

1004

SCSI Gross Error

SCSI Controller
detected a
catastrophic error
condition.

1005

Illegal SCSI Cnt Cmd

SCSI Controller did
not recognize the
command.

1007

SCSI Invalid Element

SCSI Process
detected an
unexpected error
condition.

1009

SCSI Invalid Int

SCSI Controller
posted an unexpected
interrupt.

1020

No Active Command

1021

SCSI Invalid Request

1022

SCSI Invalid
Semaphore

1023

SCSI Invalid State

SCSI Process
Queuing Error

Faulty SCSI cabling
or
Robotics Assembly

1024

SCSI Invalid Ctl Msg

1025

Overlapped Ctl Cmds

1026

Overlapped Ctl Msgs

SCSI Process
Queuing Error

Robotics Assembly

Press the Exit button and
continue.

Tandberg SLR Autoloader Service and Repair Manual

Содержание SLR AUTOLOADER - SERVICE AND





























































































Результаты поиска

Содержание SLR AUTOLOADER - SERVICE AND

Отзывы:

Tandberg Data SLR AUTOLOADER - SERVICE AND, Руководство по обслуживанию и ремонту, Страница: 63 / 92

Результаты поиска

Содержание SLR AUTOLOADER - SERVICE AND

Отзывы: