Tandberg Data SLR AUTOLOADER - SERVICE AND Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 92

Tandberg Data SLR AUTOLOADER - SERVICE AND Скачать руководство пользователя страница 60

Tandberg Data

Chapter 5 - Maintenance

7. When all sectors of the flash has been erased and programmed, the SLR

Autoloader will display the following messages.

After firmware is downloaded:

Flash Firmware

SCSI Update

Checking CRC

When programming is complete and the Autoloader reboots:

Flash Firmware

Update Successful

Please Wait While

Loader Reboots

8. Compare the Firmware ID that appears on the display panel as the unit reboots

to the Firmware ID that was present at the beginning of this procedure to verify
that the correct FW version is programmed.

Firmware upgrade via the serial port.

A new firmware may also be uploaded via the serial, debug port at the back of the
loader. To use this option the operator needs a special serial debug utility program.

Contact your Technical Support Representative for assistance if you need to use this
option.

Possible Upgrade Problems

If a power loss or a failure occurs while you are upgrading firmware, the firmware
might be corrupted. To recover from a FW upgrade failur like this, a new download
has to be performed using the serial download tool. Contact your Technical Support
Representative for assistance.

WARNING

!

Loss of power while downloading

new firmware may permanently

damage the flash memory chips.

56

Tandberg SLR Autoloader Service and Repair Manual

«
...
58
59
60
61
62
...
»

Содержание SLR AUTOLOADER - SERVICE AND





























































































Отзывы:

Нет отзывов