Tandberg Data SLR AUTOLOADER - SERVICE AND Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 92

Tandberg Data SLR AUTOLOADER - SERVICE AND Скачать руководство пользователя страница 35

Tandberg Data

Chapter 3 - Operation

Cartridge Map

When this option is selected, the operator may schroll through a list of all 8
magazine slots and the drive. For each slot and for the drive, line 3 on the display
will indicate if the slot / drive has a cartridge or not. If the Barcode scan is enabled,
the text from the barcode label is displayed.

Drive Info

The SCSI Drive communicates its Product ID (alphanumeric string), Firmware ID
(alphanumeric string), and Serial Number (factory assigned alphanumeric string) to
the SLR Autoloader firmware. When this option is selected, the operator may
schroll through a list containing this information.

Firmware Revision

This option displays the Autoloader FW revision.

Fetch Retries

Displays for each slot and for the drive, the number of cartridge fetch retries.

Stow Retries

Displays for each slot and for the drive, the number of cartridge stow retries.

Fetch Count

Displays for each slot and for the drive, the number of cartridge fetches.

Time Since Clean

Displays the drive run time since the last successful cleaning operation were
performed.

Power On Time

Displays the Power on Time for the loader.

Tandberg SLR Autoloader Service and Repair Manual

31

«
...
33
34
35
36
37
...
»

Содержание SLR AUTOLOADER - SERVICE AND





























































































Отзывы:

Нет отзывов