Tandberg Data SLR AUTOLOADER - SERVICE AND Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 92

Tandberg Data SLR AUTOLOADER - SERVICE AND Скачать руководство пользователя страница 49

Tandberg Data

Chapter 4 - Configuration

SCSI Options

Loader SCSI ID

— Sets the SCSI ID of the loader. Legal values range from 0 –

15

.

Drive SCSI ID

—

Sets the SCSI ID of the drive. Legal values range from 0 – 15

.

Loader Parity

—

Enables/Disables the parity checking for the loader SCSI bus

.

Vendor ID

— Sets the SCSI Vendor ID. The default Vendor ID is “Tandberg

Data”. Other predefined Vendor ID’s can be selected by scrolling through a list of
choices or enter a unique string by selecting the <Vendor Unique> setting.

Product ID

— Sets the SCSI Product ID. The default selection for this option is

SLR Autoloader. Other predefined Product IDs can be selected by scrolling through
a list, or entering a unique string after selecting the <Product Unique> setting.

Negotiation Mode

— Determines if SCSI negotiation is initiated by the loader.

Allowable values are Do Not Initiate or Initiate.

Transfer Rate

— Defines the SCSI burst transfer rate. Allowable values are:

•

Synchronous, 10 MB/sec

•

Synchronous, 5 MB/sec

•

Asynchronous Only.

Mode Pg 1F Length

— Defines the length of the Device Capabilities page

Parameter Length expected by a SCSI Host.

TUR Reporting

— Determines how the loader should respond to a Test Unit

Ready command if in Sequential Mode. This option is available only if sequential
mode is active.

Init Elem Status

— Determines how the loader should respond to an Initialize

Element Status command. The options are:

•

No Inventory

•

Force Inventory

•

Force Label Scan.

Unit Attn Report

— Determines if the loader should stack multiple Unit Attention

responses (ALL) or send only the highest priority Unit Attention response (One).

SCSI Mode

— Defines the loader as SCSI-2 or SCSI-3.

Tandberg SLR Autoloader Service and Repair Manual

45

«
...
47
48
49
50
51
...
»

Содержание SLR AUTOLOADER - SERVICE AND





























































































Отзывы:

Нет отзывов