Tadano TM-2000-1 Скачать руководство пользователя страница 89

Страница: 89 / 194

G - 2

Boom (Five-section boom)

W536-1040E

G - 2

3.5 Detaching the 4th boom section and

disassembling the top boom section

1. Remove the sheave (2) for extending the 4th

boom section from the 4th boom section.

2. Release the wire ropes for extending the 4th

boom section and pull out them from the 4th boom
section.

3. Remove the sheave for retractng the top boom

section and the wire rope guide from the rear end
of the 4th boom section.

4. Release the wire ropes for retracting the top boom

section and pull out them to the rear of the 4th
boom section.

5. Remove the slide plates from the side and lower

surfaces at the front end of the 4th boom section.

6. Remove the plates from the upper surface of the

4th boom section.

7. Draw out the top boom section from the 4th boom

section.

8. Remove the wire ropes for extending the top

boom section from the top boom section.

9. Remove the wire ropes for retracting the top boom

section from the top boom section.

Содержание TM-2000-1



































































































































































































Результаты поиска

Содержание TM-2000-1

Отзывы:

Похожие инструкции для TM-2000-1

Бренды по названию

Популярные бренды

Tadano TM-2000-1, Руководство по обслуживанию

Результаты поиска

Содержание TM-2000-1

Отзывы:

Похожие инструкции для TM-2000-1

Бренды по названию

Популярные бренды