Tadano TM-2000-1 Скачать руководство пользователя страница 144

Страница: 144 / 194

V - 1

Configurations of Radio-control System

Ｗ

V02-0021E

2. Safety Functions of Radio-control

System

The radio-control system has the following

functions to realize safety operations.

2.1 Auto power-off function

When the motion selection switch is not operated

for approximately one hour, the power of the
transmitter is automatically turned off to save
battery consumption.

The power LED of the transmitter is turned off.

To resume the radio-control operation, press the

power switch once again to turn on the power
LED.

2.2 Switch failure detection function

Error is displayed when the power of the

transmitter is turned on while the switches or
speed control lever is operated.

Four LEDs on the transmitter flash to show the

failure condition.

To perform a radio-control operation, press the

power switch while releasing your finger from the
other switches and the speed control lever.

Содержание TM-2000-1



































































































































































































Результаты поиска

Содержание TM-2000-1

Отзывы:

Похожие инструкции для TM-2000-1

Бренды по названию

Популярные бренды

Tadano TM-2000-1, Руководство по обслуживанию

Результаты поиска

Содержание TM-2000-1

Отзывы:

Похожие инструкции для TM-2000-1

Бренды по названию

Популярные бренды