Tadano TM-2000-1 Скачать руководство пользователя страница 79

Страница: 79 / 194

WG02-0480E

G - 1 .

General description of telescoping system

3. Relation between boom

extending/retracting operations and
wire rope mechanisms

3.1 Boom extension

・

2nd boom section:

This has no relation to any of the wire rope
mechanisms.
This is extended by the telescoping cylinder.

・

3rd boom section:

This is extended by the wire rope mechanism A.

・

4th boom section:

This is extended by the wire rope mechanism C.

・

Top boom section:

This is extended by the wire rope mechanism D.

3.2 Boom retraction

・

2nd boom section:

This has no relation to any of the wire rope
mechanisms.
This is retracted by the telescoping cylinder.

・

3rd boom section:

This is retracted by the wire rope mechanism C.

・

4th boom section:

This is retracted by the wire rope mechanism B.

・

Top boom section:

This is retracted by the wire rope mechanism E.

4. Boom telescoping order

4.1 Extending

1. When the 2nd boom section is extended, the 3rd

boom section is also extended at the same time
by the wire rope mechanism A.

2. When the 3rd boom section is extended, the 4th

boom section is also extended at the same time
by the wire rope mechanism C.

3. When the 4th boom section is extended, the top

boom section is also extended at the same time
by the wire rope mechanism D.

As a result, all of the 2nd, 3rd, 4th and top boom

sections are extended all together.

4.2 Retracting

1. When the 2nd boom section is retracted, the 4th

boom section is also retracted at the same time by
the wire rope mechanism B.

2. When the 4th boom section is retracted, the 3rd

boom section is also retracted at the same time by
the wire rope mechanism C. Additionally the top
boom is retracted at the same time by the wire
rope mechanism E as well.

As a result, all of the 2nd, 3rd, 4th and top boom

sections are retracted all together.

Содержание TM-2000-1



































































































































































































Результаты поиска

Содержание TM-2000-1

Отзывы:

Tadano TM-2000-1, Руководство по обслуживанию, Страница: 79 / 194

Результаты поиска

Содержание TM-2000-1

Отзывы: