Tadano TM-2000-1 Скачать руководство пользователя страница 182

Страница: 182 / 194

WZ02-3270E

Location of Electrical Parts

Z - 8

3. Frame

△

313-612-21001

Adjustment Procedure of Outrigger Extension Detector

1. Maximum extension detection switch adjustment procedure (upper surface of frame)

1-1.With the outrigger beams fully extended and jack cylinders fully retracted, screw the proximity switch in

until it contacts the upper surface of the outrigger box. Then loosen the switch 2.5 turns (3/32") and lock
the switch in place.

1-2.Retract the outriggers, and check the switch indicator to confirm that there is no detection error. When

shipped, the proximity switch is secured so that the switch tip is recessed loosened from the frame
internal surface by one turn 1/16 inches (1mm).

2. Middle extension detection switch adjustment procedure (side surface of frame)

Secure the proximity switch at the position in which the switch tip becomes flush for the frame internal

surface.
Operate the outrigger slides to confirm that there is no detection error.

Содержание TM-2000-1



































































































































































































Результаты поиска

Содержание TM-2000-1

Отзывы:

Tadano TM-2000-1, Руководство по обслуживанию, Страница: 182 / 194

Результаты поиска

Содержание TM-2000-1

Отзывы: