background image

 

 

G - 2  

Boom (Five-section boom) 

11 

W536-1040E 

G - 2

5. Pull out the pin fxing the boom telescoping 

cylinder to the base boom section. 

 

6. To remove the slide plates from the base boom 

section, pull out the 2nd boom section about 400 
to 600 mm (1.3 to 2 ft). 

7. Remove the slide plates from the side and lower 

surfaces at the front end of the base boom 
section. 

[NOTICE] 

When removing the slide plates from the lower 

surface, be sure to remove them with the retainers. 

 

8. Draw out the 2nd boom section and others from 

the base boom section. 

3.2  Pulling out the boom telescoping cylinder 

1. Remove the sheaves for extending the top boom 

section and the wire rope guide from the front end 
of the 4th boom section. 

2. Remove the wire ropes for extending the top 

boom section from the front end of the 3rd boom 
section and fix them at the front end of the top 
boom section with a wire etc. 

[NOTICE] 

Before removing the wire ropes, measure and 

record the dimension Ld, which can be used for 
reference during reassembly. 

3. Remove the wire ropes for retracting the top boom 

section from the front end of the 3rd boom section 
and fix them at the front end of the 4th boom 
section with a wire etc. 

 

Содержание TM-2000-1



































































































































































































Отзывы: