manualshive.com logo in svg

Tadano TM-2000-1, Руководство по обслуживанию, Страница: 100 / 194

Поделиться
Скачать
Tadano TM-2000-1 Скачать руководство пользователя страница 100

 

 

G - 2  

Boom (Five-section boom) 

25 

W536-1040E 

G - 2

7.3  Assembling the 3rd boom section 

1. Install the slide plates to the lower surface at the 

front end of the 3rd boom section. 

2. Install the slide plates to the side surfaces at the 

front end of the 3rd boom section.    Adjust the 
clearances to the following by increasing or 
decreasing the number of shims. 
- 0.5 mm (1/64 in) or less in total when the values 
at right and left are added 

[NOTICE] 

Try to minimize the difference between the right and 

left clearances. 

 

3. Release the wire ropes for extending the 4th 

boom section.    Attach the support to an end of 
the wire rope for extending the 4th boom section. 
(for two wire ropes) 

[NOTICE] 

Pay attention to the direction of the support. 

 

4. Position the support with the wire rope by 

pressing it against the stopper at the front end of 
the 3rd boom section and fix the support in that 
condition to the 3rd boom section. (for two wire 
ropes) 

 

5. Pass the wire ropes for extending the 4th boom 

section from the other ends in the grooves of the 
sheaves (1) for extending the 4th boom section. 

6. Install the wire rope guide for the sheaves (1) for 

extending the 4th boom section and temporarily 
fix the wire ropes for extending the 4th boom 
section. 

 

Содержание TM-2000-1



































































































































































































Отзывы:

Нет отзывов