Tadano TM-2000-1 Скачать руководство пользователя страница 87

Страница: 87 / 194

G - 2

Boom (Five-section boom)

W536-1040E

G - 2

4. Pull and extend the 4th boom section about 200

mm (8 in).

[NOTICE]

If step 5 and subsequent steps are performed

without extending the 4th boom section, it will be
impossible to pull out the boom telescoping cylinder
from the boom.

Do not retract the 4th boom section until the 3rd

boom section is removed.

5. Remove the two guide rollers for the boom length

detector cord.

6. Remove the support for the wire rope guide at the

rear end of the 2nd boom section.

7. Remove the bolts and disassemble the support A

for the wire rope for extending the 3rd boom
section.
Remove the parts on the support A from the rear
end of the 3rd boom section.

[NOTICE]

When it is attempted to remove the support A, it will

hit the wire rope for retracting the 4th boom section.
To avoid this, slacken the wire rope for retracting
the 4th boom section as shown in the figure below
and move it to one side within the boom.

8. Remove the pin fixing the boom telescoping

cylinder to the 2nd boom section and pull out the
boom telescoping cylinder about 1 m (3.3 ft).

9. Remove the support B from the rear end of the

3rd boom section and put it on the boom
telescoping cylinder.

10. Pull out the boom telescoping cylinder with the

support B and the wire ropes for extending the 3rd
boom section from the boom.
(Mass of cylinder: approx. 600 kg (1325 lbs))

11. Remove the wire rope for retracting the 4th boom

section from the rear end of the 4th boom section.

Содержание TM-2000-1



































































































































































































Результаты поиска

Содержание TM-2000-1

Отзывы:

Похожие инструкции для TM-2000-1

Бренды по названию

Популярные бренды

Tadano TM-2000-1, Руководство по обслуживанию

Результаты поиска

Содержание TM-2000-1

Отзывы:

Похожие инструкции для TM-2000-1

Бренды по названию

Популярные бренды