Tadano TM-2000-1 Скачать руководство пользователя страница 95 | Manualshive

Страница: 95 / 194

background image

G - 2

Boom (Five-section boom)

20

W536-1040E

G - 2

7. Measure the following internal widthwise

dimension of the 4th boom section.
- At 1.0 to 1.4 m (3.3 to 4.5 ft) from the front end
(welded portion)

[NOTICE]

The measured dimension will be used when the

clearances are adjusted at step 10.

8. Apply grease to the surfaces inside the 4th boom

section on which the slide plates of the top boom
section slide.

9. Install the slide pates at the rear end of the top

boom section.

10.Adjust the clearances of the slide plates on the

side surfaces of the boom based on the
dimension measured at step 7.
Adjust the clearances to the following by
increasing or decreasing the number of shims.
- 0.5 mm (1/64 in) or less in total when the values
at right and left are added

[NOTICE]

After this adjustment, apply thread locker

(ThreeBond 1305) to screws that are used for fixing
the slide plates.

Then lightly tighten the screw and back off a quarter

turn.

11. Apply grease to the surfaces outside the top

boom section on which the slide plates of the 4th
boom section slide and the slide plates at the rear
end of the top boom section.

12. While pulling the temporary cord and the wire

ropes for retracting the top boom section to the
rear of the boom, insert the top boom section into
the 4th boom section to the point about
2 m (6.6 ft) before full retraction.

«
...
93
94
95
96
97
...
»

Содержание TM-2000-1



































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TM-2000-1

Бренд: Ultrasonic Страницы: 16

Three-Phase Running Gear

Бренд: Miller Electric Страницы: 4

Бренд: D&R ELECTRONICS Страницы: 12

Бренд: Absima Страницы: 5

Бренд: Patlite Страницы: 38

Бренд: QTS Страницы: 50

Бренд: HOLZMANN MASCHINEN Страницы: 29

Бренд: Purelogic Страницы: 60

Бренд: WELTECH Страницы: 41

Бренд: Vector Welding Страницы: 17

Бренд: fadini Страницы: 12

KPN235WEK-WELIK-DC

Бренд: Ravaglioli Страницы: 76

Бренд: Velux Страницы: 24

Бренд: Automated Logic Страницы: 3

Бренд: BHM Medical Страницы: 56

Бренд: Carel Страницы: 94

Ricon FoldOver FR2SS Series

Бренд: Wabtec Страницы: 85

Бренд: Real Time Devices Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды