Tadano TM-2000-1 Скачать руководство пользователя страница 77

Страница: 77 / 194

G - 1

General description of telescoping system

WG02-0480E

2.2 Wire rope mechanism B (for retracting the 4th boom section)

This mechanism retracts the 4th boom section at the same time when the 2nd boom section is retracted.

The wire rope is passed within the boom in the following order.

・

Rear end of the 4th boom section

→

rear end of the 2nd boom section

→

base boom section (adjuster assy)

→

equalizer sheave (on the upper surface of the 2nd boom section)

→

rear end of the 2nd boom section

→

rear end of the 4th boom section

2.3 Wire rope mechanism C (for extending the 4th boom section /retracting the 3rd boom section)

The wire rope mechanism C serves for both extending and retracting operations.

・

Extending operation: This mechanism extends the 4th boom section at the same time when the 3rd boom

section is extended.

・

Retracting operation: This mechanism retracts the 3rd boom section at the same time when the 4th boom

section is retracted.

The wire ropes are passed within the boom in the following order.

・

Front end of the base boom section

→

front end of the 3rd boom section

→

rear end of the 4th boom

section

→

front end of the 3rd boom section

Содержание TM-2000-1



































































































































































































Результаты поиска

Содержание TM-2000-1

Отзывы:

Похожие инструкции для TM-2000-1

Бренды по названию

Популярные бренды

Tadano TM-2000-1, Руководство по обслуживанию

Результаты поиска

Содержание TM-2000-1

Отзывы:

Похожие инструкции для TM-2000-1

Бренды по названию

Популярные бренды