Tadano TM-2000-1 Скачать руководство пользователя страница 103

Страница: 103 / 194

G - 2

Boom (Five-section boom)

W536-1040E

G - 2

7.4 Assembling the boom telescoping cylinder

1. Apply the following grease to the outer surface of

the boom telescoping cyliner and the support at
the front end of the cylinder.

[NOTICE]

Apply Daphne Eponex SR No. 2 grease to the outer

surface of the boom telescoping cylinder.
Apply Tadano genuine grease TNR to the support
at the front end of the cylinder.

2. Pass the wire ropes for extending the 3rd boom

section through the sheaves for extending the 3rd
boom section.

3. Install the sheaves for extending the 3rd boom

section to the support at the front end of the boom
telescoping cylinder.

4. Install the tool A to the rear end of the boom

telescoping cylinder.

5. Hook the unthreaded ends of the wire ropes for

extending the 3rd boom section on the tool A.

6. Pass the other (threaded) ends of the wire ropes

for extending the 3rd boom section through the
holes of the tool A and temporarily fix them with
nuts.
Adjust the wire ropes so that the chamfered
surface of the fitting is placed at the bottom.

[NOTICE]

Turn the wire ropes for extending the 3rd boom

section while being careful not to cause them to
kink.

7. Turn the nut until the wire rope becomes lightly

tight.

8. Put a mark at the end of the wire rope showing

the position of the chamfered surface of the wire
rope fitting.
In the figure below, the white paint shows the
position of the chamfered surface.

Содержание TM-2000-1



































































































































































































Результаты поиска

Содержание TM-2000-1

Отзывы:

Похожие инструкции для TM-2000-1

Бренды по названию

Популярные бренды

Tadano TM-2000-1, Руководство по обслуживанию

Результаты поиска

Содержание TM-2000-1

Отзывы:

Похожие инструкции для TM-2000-1

Бренды по названию

Популярные бренды