manualshive.com logo in svg

Suzuki VZR1800 2007, Руководство по обслуживанию

Поделиться
Скачать
Suzuki VZR1800 2007 Скачать руководство пользователя страница 474

ELECTRICAL SYSTEM     10-41

RELAYS

TURN SIGNAL/SIDE-STAND RELAY

The turn signal/side-stand relay is composed of the turn signal
relay, side-stand relay and diode.

INSPECTION

Before removing the turn signal/side-stand relay, check the
operation of the turn signal light.
If the turn signal light does not illuminate, inspect the bulb, turn
signal switch and circuit connection.
If the bulb, turn signal switch and circuit connection are OK, the
turn signal relay may be faulty. In this case, replace the turn sig-
nal/side-stand relay with a new one.

NOTE:
* Make sure that the battery is fully charged.
* Refer to the page 10-21 for the side-stand relay and diode

inspection.

STARTER RELAY

!

10-18

FUEL PUMP RELAY

!

6-6

COOLING FAN RELAY

!

8-8

DIODE

SIDE-STAND RELAY

TURN

SIGNAL

RELAY

Содержание VZR1800 2007


































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды