Suzuki VZR1800 2007 страница 580 Скачать руководство пользователя

Страница: 580 / 609

– 18 –

“C44” (P0156) or “C64” (P0130) O2 SENSOR (O2S) CIRCUIT
MALFUNCTION (FOR E-02, 19, 24, 51)

INSPECTION
Step 1
(When indicating C44/P0156 for O2 sensor #2)

(When indicating C64/P0130 for O2 sensor #1)

1) Turn the ignition switch OFF.
2) Check the O2 sensor for loose or poor contacts.

If OK, then check the O2 sensor lead wire continuity.

3) Disconnect the O2 sensor coupler.
4) Check the continuity between W/G (#1) or W/Bl (#2) wire

and ground.

5) Also, check the continuity between W/G (#1) or W/Bl (#2)

wire

and B/Br wire

. If the sound is not heard from the

tester, the circuit condition is OK.



09900-25008: Multi-circuit tester set



Tester knob indication: Continuity test (



)

DETECTED CONDITION

POSSIBLE CAUSE

C44/C64
(P0156/
P0130)

O2 sensor output voltage is not input to
ECM during engine operation and run-
ning condition.
(Sensor voltage < 0.45 V)

• O2 sensor circuit open or shorted to ground.
• Fuel system malfunction.
• ECM malfunction.

ECM

O2 sensor #1

(Rear)

O2 sensor #2

(Front)

O2S. R

O2S. F

B/Br

W/Bl

W/G

B/Br

W/G

B/Br

W/Bl

VZR1800 ('08-MODEL) 14-19

Содержание VZR1800 2007


































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание VZR1800 2007

Отзывы:

Похожие инструкции для VZR1800 2007

Бренды по названию

Популярные бренды

Suzuki VZR1800 2007, Руководство по обслуживанию

Результаты поиска

Содержание VZR1800 2007

Отзывы:

Похожие инструкции для VZR1800 2007

Бренды по названию

Популярные бренды