Suzuki VZR1800 2007 Скачать руководство пользователя страница 118

Страница: 118 / 609

ENGINE 3-61

GEARSHIFT FORK GROOVE WIDTH

• Measure the gearshift fork groove width using the vernier cali-

pers.

Shift fork groove width:

Standard: 5.0 – 5.1 mm (0.197 – 0.201 in)

09900-20102: Vernier calipers

GEARSHIFT FORK THICKNESS

• Measure the gearshift fork thickness using the vernier cali-

pers.

Shift fork thickness:

Standard: 4.8 – 4.9 mm (0.189 – 0.193 in)

09900-20102: Vernier calipers

GEARSHIFT CAM BEARING AND GEARSHIFT SHAFT
BEARING
Bearing inspection

• Inspect the gearshift cam bearing for abnormal noise and

smooth rotation.

• Replace the bearings if there is anything unusual.

• Inspect the gearshift cam bearing

, gearshift shaft bearing

for abnormal noise and smooth rotation while they are in

the crankcase.

• Replace a bearing if there is anything unusual.

Bearing removal

• Remove the gearshift shaft bearing with the special tools.

09921-20210: Bearing remover
09930-30104: Sliding shaft

Содержание VZR1800 2007


































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание VZR1800 2007

Отзывы:

Бренды по названию

Популярные бренды

Suzuki VZR1800 2007, Руководство по обслуживанию

Результаты поиска

Содержание VZR1800 2007

Отзывы:

Бренды по названию

Популярные бренды