Suzuki VZR1800 2007 страница 280 Скачать руководство пользователя

Страница: 280 / 609

FI SYSTEM DIAGNOSIS 5-79

“C44” (P0156/P0161) or “C64” (P0130/P0135) HO2 SENSOR (HO2S)
CIRCUIT MALFUNCTION (FOR E-02, 19, 24)

INSPECTION
Step 1
(When indicating C44/P0156 for HO2 sensor #2)

(When indicating C64/P0130 for HO2 sensor #1)

1) Turn the ignition switch OFF.
2) Check the HO2 sensor for loose or poor contacts.

If OK, then check the HO2 sensor lead wire continuity.

3) Disconnect the HO2 sensor coupler.
4) Check the continuity between W/G (#1) or W/Bl (#2) wire

and ground.

5) Also, check the continuity between W/G (#1) or W/Bl (#2)

wire

and B/Br wire

. If the sound is not heard from the

tester, the circuit condition is OK.

09900-25008: Multi-circuit tester set

)

Tester knob indication: Continuity test (

(

)

DETECTED CONDITION

POSSIBLE CAUSE

C44/C64
(P0156/
P0130)

HO2 sensor output voltage is not input
to ECM during engine operation and
running condition.
(Sensor voltage < 0.45 V)

• HO2 sensor circuit open or shorted to ground.
• Fuel system malfunction.
• ECM malfunction.

C44/C64
(P0161/
P0135)

The heater can not operate so that
heater operation voltage is not supply to
the oxygen heater circuit.

• Battery voltage supply to the HO2 sensor.

ECM

To GP
switch

Engine stop
switch

Side-stand
relay

Ignition
switch

HO2 sensor #1

(Rear)

HO2 sensor #2

(Front)

HO2S. R

HO2S. F

HO2. H

B/Br

W/Bl

W/G

W/B

O/B

W/B

B/Br

W/G

O/B

W/B

B/Br

W/Bl

O/B

]

Содержание VZR1800 2007


































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание VZR1800 2007

Отзывы:

Похожие инструкции для VZR1800 2007

Бренды по названию

Популярные бренды

Suzuki VZR1800 2007, Руководство по обслуживанию

Результаты поиска

Содержание VZR1800 2007

Отзывы:

Похожие инструкции для VZR1800 2007

Бренды по названию

Популярные бренды