Suzuki VZR1800 2007 страница 443 Скачать руководство пользователя

Страница: 443 / 609

10-10 ELECTRICAL SYSTEM

REGULATED VOLTAGE

• Remove the front seat. (

9-4)

• Start the engine and keep it running at 5 000 r/min with the

dimmer switch turned HI position.

• Measure the DC voltage between the

and

battery termi-

nals using the multi-circuit tester. If the voltage is not within
the specified value, inspect the generator and regulator/recti-
fier. (

10-10 and -11)

NOTE:
When making this test, be sure that the battery is in fully-charged
condition.

09900-25008: Multi-circuit tester set

Tester knob indication: Voltage (

)

Regulated voltage (Charging output):

14.0 – 15.5 V at 5 000 r/min

GENERATOR COIL RESISTANCE

• Remove the fuel tank. (

6-3)

• Remove the left frame side cover. (

9-5)

• Remove the left frame lower side cover. (

3-6)

• Disconnect the generator coupler

• Measure the resistance between the three lead wires.

If the resistance is out of specified value, replace the stator
with a new one. Also, check that the generator core is insu-
lated properly.

09900-25008: Multi-circuit tester set

(

Tester knob indication: Resistance (

Ω

)

Generator coil resistance: 0.2 – 1.5

Ω

(Black – Black)

∞

Ω

(Black – Ground)

NOTE:
When making above test, it is not necessary to remove the gen-
erator.

Battery

DCV

Содержание VZR1800 2007


































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание VZR1800 2007

Отзывы:

Похожие инструкции для VZR1800 2007

Бренды по названию

Популярные бренды

Suzuki VZR1800 2007, Руководство по обслуживанию

Результаты поиска

Содержание VZR1800 2007

Отзывы:

Похожие инструкции для VZR1800 2007

Бренды по названию

Популярные бренды