manualshive.com logo in svg

Suzuki VZR1800 2007, Руководство по обслуживанию

Поделиться
Скачать
Suzuki VZR1800 2007 Скачать руководство пользователя страница 210

FI SYSTEM DIAGNOSIS     5-9

USING THE MULTI-CIRCUIT TESTER

• Use the Suzuki multi-circuit tester set (09900-25008).
• Use well-charged batteries in the tester.
• Be sure to set the tester to the correct testing range.

USING THE TESTER

• Incorrectly connecting the 

+

 and 

-

 probes may cause the

inside of the tester to burnout.

• If the voltage and current are not known, make measure-

ments using the highest range.

• When measuring the resistance with the multi-circuit tester 

1

,

∞

 will be shown as 10.00 M

Ω

 and “1” flashes in the display.

• Check that no voltage is applied before making the measure-

ment. If voltage is applied the tester may be damaged.

• After using the tester, turn the power off.

!

09900-25008: Multi-circuit tester set

NOTE:
* When connecting the multi-circuit tester, use the needle

pointed probe to the back side of the lead wire coupler and
connect the probes of tester to them.

* Use the needle pointed probe to prevent the rubber of the

water proof coupler from damage.

!

09900-25009: Needle pointed probe set

Содержание VZR1800 2007


































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды