manualshive.com logo in svg

Suzuki VZR1800 2007, Руководство по обслуживанию

Поделиться
Скачать
Suzuki VZR1800 2007 Скачать руководство пользователя страница 163

3-106     ENGINE

• Pull the cam chain lightly.
• The intake camshaft sprocket has an arrow marked “1” 

C

.

Turn the intake camshaft so that the arrow is aligned with the
gasket surface of the cylinder head.

• Engage the cam chain with the intake camshaft sprocket.
• The other arrow marked “2” 

D

 should now be pointing straight

up. Starting from the roller pin that is directly above the arrow
marked “2” 

D

, count out 18 roller pins (from the intake cam-

shaft side going towards the exhaust camshaft side).

• Engage the 18th roller pin 

E

 on the cam chain with the arrow

marked “3” on the exhaust sprocket.

NOTE:
The cam chain should now be on all three sprockets. Be careful
not to move the crankshaft until the camshaft journal holders
and cam chain tension adjuster are secured.

Содержание VZR1800 2007


































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды